Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ALCOM 3D TCE PC 5020 16116 - PC-X20 - MOCOM Compounds GmbH & Co. KG

Material Data Center offers the following functions for ALCOM 3D TCE PC 5020 16116:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Alcom datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Механические свойства - Электрические свойства - Прочие свойства
Любая форма использования представленной информации должна осуществляться на основании заявленных условий и с учетом отсутствия ответственности создателей системы.
Описание продукта
Base PolymerPolycarbonate
Filler/Additive System20 % special filler
Special Featuresincreased thermal conductivity,antistatic,heat stabilised
Market SegmentLighting,electrical and electronic
Application AreaExtrusion of 3D printable FDM filaments
Typical Applicationsfunctional components
Механические свойстваЗначениеЕдиницаСтандарт
Данные ISO
Модуль упругости при растяжении 2450 МПа ISO 527
Ударная вязкость по Шарпи, +23°C 60 кДж/м2 ISO 179/1eU
Ударная вязкость по Шарпи с надрезом, +23°C 8 кДж/м2 ISO 179/1eA
Электрические свойстваЗначениеЕдиницаСтандарт
Данные ISO
Удельное поверхностное сопротивление 100 Ом IEC 62631-3-2
Прочие свойстваЗначениеЕдиницаСтандарт
Плотность 1290 кг/м³ ISO 1183
Особые свойства и характеристики
Способы переработки
Литье под давлением
Особые показатели
Повышенная электропроводность, Антистатический, Термостабилизированный или стойкий к воздействию тепла
Применение
Электрические и электронные устройства, Filament for 3D Printing
Доступность материала по регионам
Северная Америка, Европа, Страны Азии и Тихого океана, Ближний Восток и Африка
Другая текстовая информация
Литье под давлением
Pre-Drying Conditionsin a dry air (dessiccant) dryer 100-120 °C
for 2-3 h
dependant on moisture content
max. moisture content <0,02 %
Processing Injection MouldingFilament extrusion melt temperature 250-270 °C
Recommendations for 3D print depending on printertype
3D print Nozzle temperature 300-320 °C
3D print Bed temperature 80-120 °C
3D print Print speed 10-60 mm/s
Additional 3D Printing Surface recommended
Storagedry, protected from light
Дискламация
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Создан: Источник: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.