Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RAVAMID® R200 GF15 F - PA6-GF15 - Ravago Group

Material Data Center offers the following functions for RAVAMID® R200 GF15 F:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Ravamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez, MFI 25 g/10min ISO 1133
Temperatura 250 °C -
Carga 2.16 kg -
ASTM Dados
Contração após a moldagem, paralelo 0.0075 mm/mm ASTM D 955
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Tensão na ruptura 80 MPa ISO 527
Deformação na ruptura 5 % ISO 527
Módulo de flexão, 23°C 4100 MPa ISO 178
Resistência à flexão 80 MPa ISO 178
Impacto Izod com entalhe, +23°C 5.5 kJ/m² ISO 180/1A
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 230 °C ISO 11357-1/-3
Temperatura de deflexão térmica, 1.80 MPa 150[ann.] °C ISO 75-1/-2
Temperatura de amolecimento Vicat, B 200 °C ISO 306
Flamabilidade a 1.5mm esp. nom. HB class IEC 60695-11-10
Espessuras do tubo de teste 1.6 mm -
Flamabilidade a espessura h HB class IEC 60695-11-10
Espessuras do tubo de teste 3.2 mm -
Glow Wire Flammability Index (GWFI) 650 °C IEC 60695-2-12
GWFI - thickness tested (1) 2 mm -
ann.: annealed
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1220 kg/m³ ISO 1183
Absorção de água, 24hr 1.1 % ASTM D 570
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 75 °C -
Pré-secagem - tempo 3 - 4 h -
Umidade do processamento ≤0.12 % -
Temperatura da massa 240 - 270 °C -
Temperatura do molde 70 - 90 °C -
Zona 1 220 - 230 °C -
Zona 2 230 - 245 °C -
Zona 3 250 - 260 °C -
Temperatura do bico 250 - 260 °C -
Velocidade de parafuso 50 - 80 rpm -
Contrapressão 0.4 - 0.8 MPa -
Pressão de recalque 6 - 8 MPa -
Características
Disponibilidade regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.