Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of CELANEX® 1632Z - PBT-GF15 - Celanese

Material Data Center offers the following functions for CELANEX® 1632Z:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Celanex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Outras propriedades
Any use of this information falls under the rules of our disclaimer.
Informação do produto
Celanex 1632Z is a general purpose, 15% fiberglass reinforced polybutylene terephthalate with a good balance of mechanical properties and processability.

Flammability at thickness h (0.8 mm)HB-
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Contração após a moldagem, paralelo 0.5 % ISO 294-4, 2577
Contração após a moldagem, perpendicular 1.0 % ISO 294-4, 2577
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 5400 MPa ISO 527
Tensão na ruptura 95 MPa ISO 527
Deformação na ruptura 5.4 % ISO 527
Res. impacto Charpy c/entalhe, +23°C 5.4 kJ/m² ISO 179/1eA
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 225 °C ISO 11357-1/-3
Temp. de transição vítrea, 10°C/min 60 °C ISO 11357-1/-2
Temperatura de deflexão térmica, 1.80 MPa 189 °C ISO 75-1/-2
Temperatura de deflexão térmica, 0.45 MPa 217 °C ISO 75-1/-2
Coef. de expansão térmica linear, paralelo 40 E-6/K ISO 11359-1/-2
Coef. de expansão térmica linear, perpend. 110 E-6/K ISO 11359-1/-2
Flamabilidade a espessura h HB class IEC 60695-11-10
Espessuras do tubo de teste 0.8 mm -
Outras propriedadesValorUnidadeMétodo de ensaio
Absorção de umidade 0.1 % Sim. to ISO 62
Densidade 1410 kg/m³ ISO 1183
Características
Processamento
Moldagem por injeção
Forma de entrega
Granulos
Aditivos
Lubrificantes
Aplicaciones
Polivalente
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África
Outras informações
Moldagem por injeção
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided. Up to 25% clean and dry regrind may be used.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.