Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL™ Resin CRX1005 - Europe - (PPE+PS) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL™ Resin CRX1005 - Europe:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
제품 설명서
NORYL™ CRX1005 resin is a non-reinforced blend of polyphenylene ether (PPE) + high impact polystyrene (HIPS). This injection moldable and extrusion grade was developed with improved chemical resistance and exhibits low moisture absorption, creep resistance, dimensional stability, and hydrolytic stability.
Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 6 cm³/10min ISO 1133
온도 280 °C -
하중 5 kg -
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 1750 MPa ISO 527
항복강도 35 MPa ISO 527
항복변형률 3 % ISO 527
파단시 강도 35 MPa ISO 527
파단시 신율 50 % ISO 527
굴곡 계수 1800 MPa ISO 178
Izod impact strength, +23°C, 4mm 50 kJ/m² ISO 180/1U
Izod impact strength, -30°C, 4mm 50 kJ/m² ISO 180/1U
아이조드 노치 충격 강도, +23°C, 4mm 21 kJ/m² ISO 180/1A
아이조드 노치 충격 강도, -30°C, 4mm 16 kJ/m² ISO 180/1A
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 95 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 105 °C ISO 75-1/-2
비카트 연화 온도, 120°C/h 50N 110 °C ISO 306
기타 특성값단위시험규격
밀도 1080 kg/m³ ISO 1183
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 80 - 100 °C -
Pre-drying - Time 2 - 4 h -
용융수지온도 280 - 300 °C -
성형온도 60 - 100 °C -
Feed temperature 60 - 80 °C -
Zone 1 240 - 260 °C -
Zone 2 260 - 280 °C -
Zone 3 280 - 300 °C -
특징
생산 공정
사출 성형
내화학성에
General Chemical Resistance, Hydrolytically Stable
지역별 검색
짱쨌쨈
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.