Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL™ Resin CRX1005 - Europe - (PPE+PS) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL™ Resin CRX1005 - Europe:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caractéristiques des transformations/physiques - Propriétés mécaniques - Propriétés thermiques - Propriétés diverses - Recommandations pour la transformation Moulage par injection
Any use of this information falls under the rules of our disclaimer.
Informations produit
NORYL™ CRX1005 resin is a non-reinforced blend of polyphenylene ether (PPE) + high impact polystyrene (HIPS). This injection moldable and extrusion grade was developed with improved chemical resistance and exhibits low moisture absorption, creep resistance, dimensional stability, and hydrolytic stability.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ISO Data
Indice de fluidité à chaud en volume, MVR 6 cm³/10min ISO 1133
Température 280 °C -
Charge 5 kg -
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Module en traction 1750 MPa ISO 527
Contrainte d'écoulement 35 MPa ISO 527
Déformation au seuil d'écoulement 3 % ISO 527
Contrainte à la rupture 35 MPa ISO 527
Déformation à la rupture 50 % ISO 527
Module de flexion 1800 MPa ISO 178
Izod impact strength, +23°C, 4mm 50 kJ/m² ISO 180/1U
Izod impact strength, -30°C, 4mm 50 kJ/m² ISO 180/1U
Résistance au choc Izod (entaillé), +23°C, 4mm 21 kJ/m² ISO 180/1A
Résistance au choc Izod (entaillé), -30°C, 4mm 16 kJ/m² ISO 180/1A
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fléchissement s/chrg, 1.80 MPa 95 °C ISO 75-1/-2
Température de fléchissement s/chrg, 0.45 MPa 105 °C ISO 75-1/-2
Température de ramolliss. Vicat, 120°C/h 50N 110 °C ISO 306
Propriétés diversesValeurUnitéNorme du test
Masse volumique 1080 kg/m³ ISO 1183
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 80 - 100 °C -
Pré-séchage - temps 2 - 4 h -
Température de la matière fondue 280 - 300 °C -
Température du moule 60 - 100 °C -
Température - Zone d'alimentation 60 - 80 °C -
Zone 1 240 - 260 °C -
Zone 2 260 - 280 °C -
Zone 3 280 - 300 °C -
Caractéristiques
Transformation
Moulage par injection
Résistance Chimique
Résistance chimique générale, Stabilité hydrolytique
Disponibilité régionale
Europe
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.