Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Altuglas® HFI-10 - PMMA - Altuglas International

Material Data Center offers the following functions for Altuglas® HFI-10:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Altuglas datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics단위시험규격
ISO 데이터
용융 흐름성, MFI 3 g/10min ISO 1133
온도 230 °C -
负荷 3.8 kg -
용융 비열용량 2090 J/(kg K) -
ASTM 데이터
성형 수축률, 평행 0.005 mm/mm ASTM D 955
기계적 특성단위시험규격
ISO 데이터
인장 강도 38 MPa ISO 527
파단시 신율 30 % ISO 527
굴곡 계수, 23°C 1700 MPa ISO 178
챠피 충격 강도, +23°C 40 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 4 kJ/m² ISO 179/1eA
아이조드 충격은 노치, +23°C 5 kJ/m² ISO 180/1A
ASTM 데이터
로크웰 경도 M 38 - ASTM D 785
열적 특성단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 81 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 85 °C ISO 75-1/-2
비카트 연화 온도, B 90 °C ISO 306
ASTM 데이터
UL94 난연성 HB - UL 94
열팽창 계수, 평행 100 E-6/K ASTM D 696
전기적 특성단위시험규격
ASTM 데이터
전기 압력, 단기간의 15 kV/mm ASTM D 149
소산 인자, 1 MHz 0.04 - ASTM D 150
상대 유전율, 60 Hz 3.9 - ASTM D 150
표면 저항 1E14 Ohm ASTM D 257
부피 저항 >1E15 Ohm*cm ASTM D 257
광학 특성단위시험규격
ASTM 데이터
탁도 2 % ASTM D 1003
광선 투겠淅 90 % ASTM D 1003
기타 특성단위시험규격
조건에서의 흡습성 0.36 % ISO 62와 유사
밀도 1150 kg/m³ ISO 1183
Processing Recommendation Injection Molding단위시험규격
Pre-drying - Temperature 80 °C -
Pre-drying - Time 4 h -
용융수지온도 230 - 240 °C -
성형온도 75 - 85 °C -
특징
생산 공정
사출 성형
특별 특성
고충격 또는 고충격 보강, 투명도
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.