Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Altuglas® HFI-10 - PMMA - Altuglas International

Material Data Center offers the following functions for Altuglas® HFI-10:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Altuglas datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Melt flow index, MFI 3 g/10min ISO 1133
Temperature 230 °C -
Load 3.8 kg -
Spec. heat capacity of melt 2090 J/(kg K) -
ASTM Data
Mold Shrinkage, MD 0.005 mm/mm ASTM D 955
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Strength 38 MPa ISO 527
Strain at break 30 % ISO 527
Flexural modulus, 23°C 1700 MPa ISO 178
Charpy impact strength, +23°C 40 kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 4 kJ/m² ISO 179/1eA
Izod notched impact strength, +23°C 5 kJ/m² ISO 180/1A
ASTM Data
Rockwell Hardness M 38 - ASTM D 785
Thermal propertiesValueUnitTest Standard
ISO Data
Temp. of deflection under load, 1.80 MPa 81 °C ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa 85 °C ISO 75-1/-2
Vicat softening temperature, B 90 °C ISO 306
ASTM Data
UL 94 Flame rating HB - UL 94
Coefficient of Thermal Expansion, MD 100 E-6/K ASTM D 696
Electrical propertiesValueUnitTest Standard
ASTM Data
Dielectric Strength, Short Time 15 kV/mm ASTM D 149
Dissipation Factor, 1 MHz 0.04 - ASTM D 150
Dielectric Constant, 60 Hz 3.9 - ASTM D 150
Surface Resistivity 1E14 Ohm ASTM D 257
Volume Resistivity >1E15 Ohm*cm ASTM D 257
Optical propertiesValueUnitTest Standard
ASTM Data
Haze 2 % ASTM D 1003
Light Transmittance 90 % ASTM D 1003
Other propertiesValueUnitTest Standard
Humidity absorption 0.36 % Sim. to ISO 62
Density 1150 kg/m³ ISO 1183
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 80 °C -
Pre-drying - Time 4 h -
Melt temperature 230 - 240 °C -
Mold temperature 75 - 85 °C -
Characteristics
Processing
Injection Molding
Special Characteristics
High impact or impact modified, Transparent
Regional Availability
North America, Europe, Asia Pacific, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.