Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin SF2250 - Americas - PEI-GF - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for ULTEM™ Resin SF2250 - Americas:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Testo del prodotto
High flow ULTEM for thin wall application

UL Yellow Card Link E207780-100116343
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 40 cm³/10min ISO 1133
Temperatura 345 °C -
Carico 10 kg -
ASTM Data
Indice di fluidità a caldo, MFI 19.7 g/10min ASTM D 1238
Temperatura 337 °C -
Carico 6.6 kg -
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Carico unitario a rottura 157 MPa ISO 527
Deformazione a rottura 3 % ISO 527
Modulo a flessione 7150 MPa ISO 178
Resist. urto Izod con intaglio, +23°C, 4mm 9 kJ/m² ISO 180/1A
ASTM Data
Modulo a trazione 8900 MPa ASTM D 638
Resistenza alla trazione a rottura 162 MPa ASTM D 638
Allungamento a rottura 3 % ASTM D 638
Modulo a flessione 7260 MPa ASTM D 790
Resistenza all'urto Izod con intaglio, 1/8 in 89 J/m ASTM D 256
Proprietà TermicheValoreUnitáNorma del test
ASTM Data
DTUL a 264 psi 203 °C ASTM D 648
Altre ProprietàValoreUnitáNorma del test
Massa volumica 1440 kg/m³ ISO 1183
Densità 1440 kg/m³ ASTM D 792
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 150 °C -
Pre-essiccamento - Tempo 4 - 6 h -
Umidità del Processo ≤0.02 % -
Temperatura di fusione 350 - 400 °C -
Temperatura dello stampo 135 - 165 °C -
Zona 1 330 - 400 °C -
Zona 2 340 - 400 °C -
Zona 3 345 - 400 °C -
Velocità di Rotazione della Vite 40 - 70 rpm -
Contropressione 0.3 - 0.7 MPa -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Disponibilità geografica
Nord America
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.