Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin SF2250 - Americas - PEI-GF - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for ULTEM™ Resin SF2250 - Americas:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caractéristiques des transformations/physiques - Propriétés mécaniques - Propriétés thermiques - Propriétés diverses - Recommandations pour la transformation Moulage par injection
Any use of this information falls under the rules of our disclaimer.
Informations produit
High flow ULTEM for thin wall application

UL Yellow Card Link E207780-100116343
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ISO Data
Indice de fluidité à chaud en volume, MVR 40 cm³/10min ISO 1133
Température 345 °C -
Charge 10 kg -
ASTM Data
Indice de fluidité, MFI 19.7 g/10min ASTM D 1238
Température 337 °C -
Charge 6.6 kg -
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Contrainte à la rupture 157 MPa ISO 527
Déformation à la rupture 3 % ISO 527
Module de flexion 7150 MPa ISO 178
Résistance au choc Izod (entaillé), +23°C, 4mm 9 kJ/m² ISO 180/1A
ASTM Data
Module en traction 8900 MPa ASTM D 638
Résistance de traction à la rupture 162 MPa ASTM D 638
Allongement à la rupture 3 % ASTM D 638
Module de flexion 7260 MPa ASTM D 790
Izod choc avec entaille, 1/8 in 89 J/m ASTM D 256
Propriétés thermiquesValeurUnitéNorme du test
ASTM Data
DTUL à 264 psi 203 °C ASTM D 648
Propriétés diversesValeurUnitéNorme du test
Masse volumique 1440 kg/m³ ISO 1183
Densité 1440 kg/m³ ASTM D 792
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 150 °C -
Pré-séchage - temps 4 - 6 h -
L'humidité de traitement ≤0.02 % -
Température de la matière fondue 350 - 400 °C -
Température du moule 135 - 165 °C -
Zone 1 330 - 400 °C -
Zone 2 340 - 400 °C -
Zone 3 345 - 400 °C -
Vitesse de rotation de vis 40 - 70 rpm -
Contre-pression 0.3 - 0.7 MPa -
Caractéristiques
Transformation
Moulage par injection
Disponibilité régionale
Amérique du nord
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.