Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Reny 2502A - PAMXD6-(GF+MX)20 - Mitsubishi Engineering-Plastics Corporation

Material Data Center offers the following functions for Reny 2502A:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Reny datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristicsdry / condUnitTest Standard
ISO Data
Melt volume-flow rate, MVR 14 / * cm³/10min ISO 1133
Temperature 275 / * °C -
Load 2.16 / * kg -
Melt flow index, MFI 21.6 g/10min ISO 1133
Temperature 275 °C -
Load 2.16 kg -
Molding shrinkage, parallel 0.5 / * % ISO 294-4, 2577
Mechanical propertiesdry / condUnitTest Standard
ISO Data
Tensile Modulus 18400 / 14900 MPa ISO 527
Stress at break 150 / 120 MPa ISO 527
Strain at break 1.2 / 1.3 % ISO 527
Flexural modulus, 23°C 16500 / 14700 MPa ISO 178
Charpy impact strength, +23°C 27 / 29 kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 4.1 / 4.3 kJ/m² ISO 179/1eA
Thermal propertiesdry / condUnitTest Standard
ISO Data
Temp. of deflection under load, 1.80 MPa 217 / * °C ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa 235 / * °C ISO 75-1/-2
Coeff. of linear therm. expansion, parallel 20 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion, normal 30 / * E-6/K ISO 11359-1/-2
Burning behav. at 1.5 mm nom. thickn. V-0 / * class IEC 60695-11-10
Thickness tested 1.6 / * mm -
Yellow Card available yes / * - -
Electrical propertiesdry / condUnitTest Standard
ISO Data
Relative permittivity, 100Hz - / 5 - IEC 62631-2-1
Relative permittivity, 1MHz - / 5 - IEC 62631-2-1
Dissipation factor, 100Hz - / 500 E-4 IEC 62631-2-1
Dissipation factor, 1MHz - / 170 E-4 IEC 62631-2-1
Volume resistivity 2E14 / 1E13 Ohm*m IEC 62631-3-1
Surface resistivity * / 2E14 Ohm IEC 62631-3-2
Electric strength 27 / 26 kV/mm IEC 60243-1
Comparative tracking index 200 / 300 - IEC 60112
Other propertiesdry / condUnitTest Standard
Humidity absorption 0.9 / * % Sim. to ISO 62
Density 1660 / - kg/m³ ISO 1183
Characteristics
Special Characteristics
Flame retardant
Regional Availability
North America, Europe, Asia Pacific
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.