Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of PLEXIGLAS® Optical POQ66 - PMMA - Röhm GmbH
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, parameters for material models, CAE Interfaces
Check here, which other Plexiglas datasheets, application examples or technical articles are available in Material Data Center
•优异透光率和光亮度
•优异的机械性能
, 表面硬度和抗磨损性 •优异耐候性PLEXIGLAS® Optical POQ66 特殊性能如下: •可靠的纯度和清澈度•中等到长光程下的高导光
/照明效率 •在厚壁下也保持物料原色应用:
适用于光学要求苛刻的挤出板材。
应用实例
:中尺寸到大尺寸的挤出导光板加工方法
: PLEXIGLAS® Optical POQ66 可用常见的三段式挤出 机成型为工程用的热塑性塑料建议用加工温度范围内的较低温度来生产导光板
模塑料物理形态
/包装: PLEXIGLAS® Optical POQ66 模塑料成品是粒径均匀 的粒料, 有多种包装;也可应顾客要求包装。加工/物理特性 | 价值 | 单位 | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO数据 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
熔体体积流动速度, MVR | 2.3 | cm³/10min | ISO 1133 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
温度 | 230 | °C | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
载荷 | 3.8 | kg | - |
机械性能 | 价值 | 单位 | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO数据 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
拉伸模量 | 3200 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
断裂应力 | 69 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
断裂伸长率 | 4 | % | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
无缺口简支梁冲击强度, +23°C | 20 | kJ/m² | ISO 179/1eU |
热性能 | 价值 | 单位 | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO数据 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
玻璃化转变温度, 10°C/min | 108 | °C | ISO 11357-1/-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
维卡软化温度, B | 104 | °C | ISO 306 |
电性能 | 价值 | 单位 | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO数据 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
体积电阻率 | >1E13 | Ohm*m | IEC 62631-3-1 |
光学特性 | 价值 | 单位 | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Data | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
光输送 | 92 | % | ISO 13468-1, -2 |
其它性能 | 价值 | 单位 | Test Standard |
密度 | 1190 | kg/m³ | ISO 1183 |
试样制备条件 | 价值 | 单位 | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO数据 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO试样制备条件. | 8257 | - | ISO ....-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
注塑, 模具温度 | 64 | °C | ISO 294 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
注塑, 注射速度 | 195 | mm/s | ISO 294 |
预干燥温度: 最高94℃
在除湿型干燥器中的预干燥时间: 2-3h
PROCESSING
熔融温度: 220-260℃
口模温度: 220-260℃
预干燥温度: 最高94℃
在除湿型干燥器中的预干燥时间: 2-3h
PROCESSING
熔融温度: 220-260℃
口模温度: 220-260℃
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.