Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of HOSTAFORM® C 13031 XAP® - POM - Celanese

Material Data Center offers the following functions for HOSTAFORM® C 13031 XAP®:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Hostaform datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
加工/物理特性 - 机械性能 - 热性能 - 电性能 - 其它性能 - 函数
Any use of this information falls under the rules of our disclaimer.
加工/物理特性价值单位Test Standard
ISO数据
熔体体积流动速度, MVR 12 cm³/10min ISO 1133
温度 190 °C -
载荷 2.16 kg -
模塑收缩率, 平行 2.0 % ISO 294-4, 2577
模塑收缩率, 垂直 1.8 % ISO 294-4, 2577
熔体 0.155 W/(m K) -
机械性能价值单位Test Standard
ISO数据
拉伸模量 3050 MPa ISO 527
屈服应力 68 MPa ISO 527
屈服伸长率 8 % ISO 527
名义断裂伸长率 28 % ISO 527
无缺口简支梁冲击强度, +23°C 200 kJ/m² ISO 179/1eU
简支梁冲击强度, -30°C 200 kJ/m² ISO 179/1eU
简支梁缺口冲击强度, +23°C 6.7 kJ/m² ISO 179/1eA
简支梁缺口冲击强度, -30°C 6 kJ/m² ISO 179/1eA
热性能价值单位Test Standard
ISO数据
熔融温度, 10°C/min 170 °C ISO 11357-1/-3
热变形温度, 1.80 MPa 107 °C ISO 75-1/-2
线性热膨胀系数, 平行 110 E-6/K ISO 11359-1/-2
电性能价值单位Test Standard
ISO数据
相对介电常数., 100Hz 4 - IEC 62631-2-1
相对介电常数., 1MHz 4 - IEC 62631-2-1
介质损耗因子, 100Hz 20 E-4 IEC 62631-2-1
介质损耗因子, 1MHz 50 E-4 IEC 62631-2-1
体积电阻率 1E12 Ohm*m IEC 62631-3-1
表面电阻率 1E14 Ohm IEC 62631-3-2
介电强度 35 kV/mm IEC 60243-1
其它性能价值单位Test Standard
吸水性 0.65 % 类似ISO 62
吸湿性 0.2 % 类似ISO 62
密度 1410 kg/m³ ISO 1183
函数
粘度－剪切速度 , HOSTAFORM® C 13031 XAP®, POM, Celanese
剪切应力－剪切速度 , HOSTAFORM® C 13031 XAP®, POM, Celanese
应力－应变. , HOSTAFORM® C 13031 XAP®, POM, Celanese
正割模量－应变. , HOSTAFORM® C 13031 XAP®, POM, Celanese
应力－应变(等时的) 23°C, HOSTAFORM® C 13031 XAP®, POM, Celanese
蠕变模量－时间. 23°C, HOSTAFORM® C 13031 XAP®, POM, Celanese
蠕变曲线 23°C, HOSTAFORM® C 13031 XAP®, POM, Celanese
典型数据
加工方法
注塑
供货形式
粒料
添加剂
脱模助剂
特征
低排放, 热稳定性, 共聚物
耐化学试剂
耐碱性, 耐溶剂性, 水解稳定, 抗氧化性
Certifications
可食品接触的, 10/2011认证, FDA 21 CFR认证
地区供应
北美, 欧洲, 亚太, 中南美洲, 中东/非洲
其他信息
注塑成型
To achive low emission values pre drying using a recirculating air dryer (100 to 120 °C / max. 40 mm layer / 3 to 6 hours) is recommended.

Max. Water content 0,1 %
Standard injection moulding machines with three phase (15 to 25 D)
plasticating screws will fit.

Conditioning e.g. moisturizing is not necessary.
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.