Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of SABIC® PP 578L - PP - Saudi Basic Industries Corporation (SABIC)
Material Data Center offers the following functions for SABIC® PP 578L:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces
Check here, which other Sabic datasheets, application examples or technical articles are available in Material Data Center
Use the following short links to get directly to the properties of interest in this datasheet:
Любая форма использования представленной информации должна осуществляться на основании заявленных
условий и с учетом отсутствия ответственности создателей системы.
Описание продукта
SABIC® PP 578L is a PP homopolymer grade which contains a well balanced antistatic and slip agent package. This grade allows for cost efficient processing on the basis of good flow behavior, short cycle times, good demoulding and robust processing behaviour. Products made from SABIC® PP 578L typically have low warpage, high stiffness in combination with moderate impact strength at room temperature, good antistatic behavior and a high gloss.
Application: SABIC® PP 578L is typically used in caps & closures and thin wall packaging both in food and non-food segments.
Health, Safety and Food Contact regulations:Material Safety Data Sheets (MSDS) and Product Safety declarations are available on our Internet site
http://www.SABIC.com
The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical / medical applications.
This grade material is UL registered under File E111275 (www.ul.com) / IMDS 7172624
| Механические свойства | Значение | Единица | Стандарт |
| Данные ISO |
| Модуль упругости при растяжении |
1700 |
МПа |
ISO 527 |
| Напряжение в точке текучести |
36 |
МПа |
ISO 527 |
| Удлинение в точке текучести |
9 |
% |
ISO 527 |
| Ударная прочность по Шарпи с надрезом, +23°C |
4 |
кДж/м2 |
ISO 179/1eA |
| Твердость по Шору D |
69 |
- |
ISO 7619-1 |
| Теплофизические свойства | Значение | Единица | Стандарт |
| Данные ISO |
| Температура изгиба под нагрузкой, 1.80 МПа |
55 |
°C |
ISO 75-1/-2 |
| Температура изгиба под нагрузкой, 0.45 МПа |
90 |
°C |
ISO 75-1/-2 |
| Температура размягчения по Вика, A |
153 |
°C |
ISO 306 |
| Температура размягчения по Вика, B |
95 |
°C |
ISO 306 |
Особые свойства и характеристики
Специальные характеристики
Гомополимер
Сертификаты
Контакт с пищей
Дискламация
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Создан: Источник: www.materialdatacenter.com
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.
