Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of ULTEM™ Resin 2200 - Americas - PEI-GF20 - Saudi Basic Industries Corporation (SABIC)
unit conversion, PDF datasheet print, comparison with other plastics
Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center
UL Yellow Card Link E121562-502535
Características de processamento/físicas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ASTM Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Índice de fluidez, MFI | 6 | g/10min | ASTM D 1238 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Temperatura | 337 | °C | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Carga | 6.6 | kg | - |
Propriedades mecânicas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ASTM Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Módulo de tração | 6890 | MPa | ASTM D 638 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistência à tração na ruptura | 131 | MPa | ASTM D 638 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Deformação na ruptura | 4 | % | ASTM D 638 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Dureza Rockwell | M 114 | - | ASTM D 785 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Impacto Izod com entalhe, 1/8 in | 64 | J/m | ASTM D 256 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistência ao Impacto Izod, 1/8 in | 480 | J/m | ASTM D 256 |
Propriedades térmicas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Flamabilidade a espessura h | V-0 | class | IEC 60695-11-10 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Espessuras do tubo de teste | 0.4 | mm | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Flamabilidade 5V a espessura h | 5VA | class | IEC 60695-11-20 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Espessuras do tubo de teste | 1.9 | mm | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ASTM Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Temperatura de amolecimento Vicat | 220 | °C | ASTM D 1525 |
Propriedades elétricas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ASTM Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistência elétrica, tempo curto | 26.3 | kV/mm | ASTM D 149 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistividade volumétrica específica | >1E15 | Ohm*cm | ASTM D 257 |
Outras propriedades | Valor | Unidade | Método de ensaio |
Densidade | 1420 | kg/m³ | ASTM D 792 |
Recomendação de processamento Moldagem por injeção | Valor | Unidade | Método de ensaio |
Pré-secagem - temperatura | 150 | °C | - |
Pré-secagem - tempo | 4 - 6 | h | - |
Umidade do processamento | ≤0.02 | % | - |
Temperatura da massa | 350 - 400 | °C | - |
Temperatura do molde | 135 - 165 | °C | - |
Zona 1 | 330 - 400 | °C | - |
Zona 2 | 340 - 400 | °C | - |
Zona 3 | 345 - 400 | °C | - |
Velocidade de parafuso | 40 - 70 | rpm | - |
Contrapressão | 0.3 - 0.7 | MPa | - |
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.