Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Rilsan® TIEFLEX S452 NAT T6L - PA* - ARKEMA

Material Data Center offers the following functions for Rilsan® TIEFLEX S452 NAT T6L:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Rilsan datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Informação do produto
Rilsan® TIEFLEX S452 NAT T6L resin is a flexible tie layer alloy partially based on renewable resources. This grade is designed for multilayer automotive and trucks lines (tie layer for fuel line). In the case of direct contact with fuel, contact Arkema representative for recommendations.

Packaging:
This grade is delivered dried in sealed packaging (25kg bags) ready to be processed.

Shelf life:
Two years from the date of delivery. For any use above this limit, please refer to our technical services.
Características de processamento/físicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez volumétrico, MVR 3.7 / * cm³/10min ISO 1133
Temperatura 235 / * °C -
Carga 5 / * kg -
Propriedades mecânicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 685 / 515 MPa ISO 527
Tensão no escoamento - / 33 MPa ISO 527
Deformação no escoamento - / 31 % ISO 527
Deformação nominal na ruptura - / >50 % ISO 527
Res. impacto Charpy c/entalhe, +23°C - / 95 kJ/m² ISO 179/1eA
Res. impacto Charpy c/entalhe, -30°C - / 6.5 kJ/m² ISO 179/1eA
Propriedades térmicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 217 / * °C ISO 11357-1/-3
Outras propriedadesSeco / CondUnidadeMétodo de ensaio
Absorção de água 2.9 / * % Sim. to ISO 62
Absorção de umidade 1.2 / * % Sim. to ISO 62
Densidade 1090 / - kg/m³ ISO 1183
Características
Processamento
Outros tipos de extrusão
Forma de entrega
Granulos, Cor natural
Certifications
Contém recursos renováveis
Disponibilidade regional
Outras informações
Outros tipos de extrusão
Processing conditions
- Typical melt temperature (min / recommended / max): 220°C / 230°C / 270°C
- Drying time and temperature (only necessary for bags opened for more than two hours): 4-6 hours at 80°C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.