Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Rilsamid® AMN BLACK P20 TLD - PA12 - ARKEMA

Material Data Center offers the following functions for Rilsamid® AMN BLACK P20 TLD:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Rilsamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Outras propriedades
Any use of this information falls under the rules of our disclaimer.
Informação do produto
PA12-P, MHLR, 12-005
Rilsamid® AMN BLACK P20 TLD resin is a black colored polyamide. This grade is plasticized and designed for injection molding.
Características de processamento/físicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez volumétrico, MVR 44 / * cm³/10min ISO 1133
Temperatura 235 / * °C -
Carga 2.16 / * kg -
Contração após a moldagem, paralelo 1.9 / * % ISO 294-4, 2577
Contração após a moldagem, perpendicular 1.9 / * % ISO 294-4, 2577
Propriedades mecânicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Módulo de tração - / 550 MPa ISO 527
Tensão no escoamento - / 31 MPa ISO 527
Deformação no escoamento - / 19 % ISO 527
Deformação nominal na ruptura - / >50 % ISO 527
Res. impacto Charpy c/entalhe, +23°C - / 18 kJ/m² ISO 179/1eA
Res. impacto Charpy c/entalhe, -30°C - / 4 kJ/m² ISO 179/1eA
Propriedades térmicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 174 / * °C ISO 11357-1/-3
Outras propriedadesSeco / CondUnidadeMétodo de ensaio
Densidade 1020 / 1020 kg/m³ ISO 1183
Características
Processamento
Moldagem por injeção
Forma de entrega
Granulos, Negro
Aditivos
Desmoldante, Plastificante
Características especiais
Estável a luz, Estabilidade a raios U.V./Intempéries, Estável contra o calor
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África
Outras informações
Moldagem por injeção

Processing conditions, Injection:

- Typical melt temperature (Min / Recommended / Max) : 250°C / 270°C / 290°C.
- Mold temperature : 20 - 40°C
- Drying time and temperature (only necessary for bags opened for more than two hours) : 4-6 hours at 80 - 90°C.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.