Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL™ Resin N1250 - Americas - (PPE+PS) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL™ Resin N1250 - Americas:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Informação do produto
NORYL™ N1250 resin is a non-reinforced blend of polyphenylene ether (PPE) + high impact polystyrene (HIPS). This injection moldable grade contains non-brominated, non-chlorinated flame retardant and carries a UL94 flame rating of 5VA at 2.5mm and V0 at 0.75mm. NORYL N1250 resin offers thin wall FR capability, enhanced dimensional stability, high heat resistance, low moisture absorption, and good electrically insulating properties. It may be an excellent candidate for a variety of consumer electronic applications such as charger and adapter housings.

UL Yellow Card Link E121562-100090216
Características de processamento/físicasValorUnidadeMétodo de ensaio
ASTM Dados
Índice de fluidez, MFI 28 g/10min ASTM D 1238
Temperatura 300 °C -
Carga 5 kg -
Propriedades mecânicasValorUnidadeMétodo de ensaio
ASTM Dados
Módulo de tração 2700 MPa ASTM D 638
Resistência à tração no escoamento 77 MPa ASTM D 638
Resistência à tração na ruptura 62 MPa ASTM D 638
Alongamento no escoamento 5 % ASTM D 638
Deformação na ruptura 15 % ASTM D 638
Módulo de flexão 2800 MPa ASTM D 790
Impacto Izod com entalhe, 1/8 in 100 J/m ASTM D 256
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Flamabilidade a espessura h V-2 class IEC 60695-11-10
Espessuras do tubo de teste 0.4 mm -
Flamabilidade 5V a espessura h 5VA class IEC 60695-11-20
Espessuras do tubo de teste 2.5 mm -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
Glow Wire Ignition Temperature (GWIT) 775 °C IEC 60695-2-13
GWIT - thickness tested (1) 1 mm -
ASTM Dados
DTUL @ 66 psi 125 °C ASTM D 648
DTUL @ 264 psi 116 °C ASTM D 648
Temperatura de amolecimento Vicat 137 °C ASTM D 1525
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1100 kg/m³ ASTM D 792
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 105 - 110 °C -
Pré-secagem - tempo 3 - 4 h -
Umidade do processamento ≤0.02 % -
Temperatura da massa 275 - 305 °C -
Temperatura do molde 70 - 100 °C -
Zona 1 245 - 295 °C -
Zona 2 255 - 300 °C -
Zona 3 265 - 305 °C -
Velocidade de parafuso 20 - 100 rpm -
Contrapressão 0.3 - 0.7 MPa -
Características
Processamento
Moldagem por injeção
Aditivos
Anti-chama
Características especiais
Retardante de chama
Aplicaciones
Automóvel
Disponibilidade regional
América do Norte
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.