Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin SF2260 - Asia - PEI - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for ULTEM™ Resin SF2260 - Asia:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
제품 설명서
High flow ULTEM for thin wall application

UL Yellow Card Link E45587-101275405
Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 70 cm³/10min ISO 1133
온도 345 °C -
하중 10 kg -
ASTM 데이터
용융 흐름성, MFI 30 g/10min ASTM D 1238
온도 337 °C -
하중 6.6 kg -
기계적 특성값단위시험규격
ISO 데이터
파단시 강도 142 MPa ISO 527
파단시 신율 2.4 % ISO 527
굴곡 계수 7170 MPa ISO 178
아이조드 노치 충격 강도, +23°C, 4mm 8 kJ/m² ISO 180/1A
ASTM 데이터
인장탄성률 9400 MPa ASTM D 638
파단시 강도 148 MPa ASTM D 638
파단시 신율 2.4 % ASTM D 638
굴곡 계수 7360 MPa ASTM D 790
아이조드 충격은 노치, 1/8 in 80 J/m ASTM D 256
열적 특성값단위시험규격
ISO 데이터
1.5mm 평균두께에서의 난연성 V-0 class IEC 60695-11-10
테스트 두께 1.5 mm -
ASTM 데이터
DTUL @ 264 psi 201 °C ASTM D 648
기타 특성값단위시험규격
밀도 1420 kg/m³ ISO 1183
밀도 1420 kg/m³ ASTM D 792
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 150 °C -
Pre-drying - Time 4 - 6 h -
Processing humidity ≤0.02 % -
용융수지온도 350 - 400 °C -
성형온도 135 - 165 °C -
Zone 1 330 - 400 °C -
Zone 2 340 - 400 °C -
Zone 3 345 - 400 °C -
Screw speed 40 - 70 rpm -
Back pressure 0.3 - 0.7 MPa -
특징
생산 공정
사출 성형
지역별 검색
쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.