Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin MD131 - Asia - PEI - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for ULTEM™ Resin MD131 - Asia:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
제품 설명서
Transparent, high flow Polyetherimide (Tg 217C). ECO Conforming. US FDA and EU Food Contact Compliant.
Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 25 cm³/10min ISO 1133
온도 360 °C -
하중 5 kg -
ASTM 데이터
용융 흐름성, MFI 17.8 g/10min ASTM D 1238
온도 337 °C -
하중 6.6 kg -
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 3200 MPa ISO 527
항복강도 105 MPa ISO 527
항복변형률 6 % ISO 527
파단시 강도 85 MPa ISO 527
파단시 신율 50 % ISO 527
굴곡 계수 3300 MPa ISO 178
챠피 노치드 충격 강도, +23°C 3 kJ/m² ISO 179/1eA
Izod impact strength, +23°C, 4mm N kJ/m² ISO 180/1U
Izod impact strength, -30°C, 4mm N kJ/m² ISO 180/1U
아이조드 노치 충격 강도, +23°C, 4mm 5 kJ/m² ISO 180/1A
아이조드 노치 충격 강도, -30°C, 4mm 5 kJ/m² ISO 180/1A
Ball indentation hardness 140 MPa ISO 2039-1
ASTM 데이터
인장탄성률 3590 MPa ASTM D 638
항복강도 110 MPa ASTM D 638
파단시 강도 105 MPa ASTM D 638
항복변형률 7 % ASTM D 638
파단시 신율 60 % ASTM D 638
굴곡 계수 3550 MPa ASTM D 790
로크웰 경도 M 109 - ASTM D 785
Taber내마모성 10 mg/1000 cycles ASTM D 1044
아이조드 충격은 노치, 1/8 in 32 J/m ASTM D 256
아이조드 충격은 노치, Low-Temperature 35 J/m ASTM D 256
온도 -30 °C -
Izod충격강도, 1/8 in 1340 J/m ASTM D 256
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 190 °C ISO 75-1/-2
비카트 연화 온도, A 215 °C ISO 306
비카트 연화 온도, B 211 °C ISO 306
비카트 연화 온도, 120°C/h 50N 212 °C ISO 306
열전도율 0.21 W/(m K) DIN 52616
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (3) 3.2 mm -
ASTM 데이터
DTUL @ 66 psi 205 °C ASTM D 648
DTUL @ 264 psi 197 °C ASTM D 648
비카트 연화 온도 218 °C ASTM D 1525
열전도율, 솔리드 0.0317 W/(m K) ASTM C 177
전기적 특성값단위시험규격
ISO 데이터
상대 유전뮬, 1MHz 2.9 - IEC 62631-2-1
소산 인자, 1MHz 60 E-4 IEC 62631-2-1
부피 저항 1E13 Ohm*m IEC 62631-3-1
표면 저항 >1E15 Ohm IEC 62631-3-2
전기 압력 33 kV/mm IEC 60243-1
CTI 150 - IEC 60112
ASTM 데이터
전기 압력, 단기간의 27.9 kV/mm ASTM D 149
부피 저항 >1E15 Ohm*cm ASTM D 257
기타 특성값단위시험규격
물에서의 흡수성 1.25 % ISO 62와 유사
조건에서의 흡습성 0.7 % ISO 62와 유사
밀도 1270 kg/m³ ISO 1183
밀도 1270 kg/m³ ASTM D 792
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 150 °C -
Pre-drying - Time 4 - 6 h -
Processing humidity ≤0.02 % -
용융수지온도 350 - 400 °C -
성형온도 135 - 165 °C -
Zone 1 330 - 400 °C -
Zone 2 340 - 400 °C -
Zone 3 345 - 400 °C -
Screw speed 40 - 70 rpm -
Back pressure 0.3 - 0.7 MPa -
특징
생산 공정
사출 성형
특별 특성
투명도
Certifications
Food contact, Food approval FDA 21 CFR
지역별 검색
쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.