Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of TECACOMP® PEEK 450 CMF white 3809 - PEEK-Z - Ensinger Compounds

Material Data Center offers the following functions for TECACOMP® PEEK 450 CMF white 3809:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Tecacomp datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
기계적 특성단위시험규격
ISO 데이터
인장탄성률 5000 MPa ISO 527
인장 강도 100 MPa ISO 527
파단시 신율 9 % ISO 527
열적 특성단위시험규격
ISO 데이터
녹는점, 10°C/min 343 °C ISO 11357-1/-3
유리 전이 온도, 10 °C/min 143 °C ISO 11357-1/-2
전기적 특성단위시험규격
ISO 데이터
전기 압력 15.8 kV/mm IEC 60243-1
Other Standards[S]
부피 저항 2.71E13 Ohm*m ISO 3915
표면 저항 3.53E15 Ohm ISO 3915
S: These properties are reported by the producer according standards that are different to our defaults.
기타 특성단위시험규격
밀도 1630 kg/m³ ISO 1183
Bulk density 870 kg/m³ -
Processing Recommendation Injection Molding단위시험규격
Pre-drying - Temperature 140 - 160 °C -
Pre-drying - Time 4 - 6 h -
Processing humidity ≤0.02 % -
용융수지온도 390 - 400 °C -
성형온도 160 - 210 °C -
Zone 1 360 - 400 °C -
특징
생산 공정
사출 성형
인도 유형
펠렛 (입자,알갱이), 화이트
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.