Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LEONA™ 14G33 - PA66-GF33 - Asahi Kasei

Material Data Center offers the following functions for LEONA™ 14G33:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Leona datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 9800 / 7800 MPa ISO 527
파단시 강도 208 / 143 MPa ISO 527
파단시 신율 4 / 6 % ISO 527
굴곡 계수, 23°C 9600 / 6700 MPa ISO 178
굴곡 강도 302 / 213 MPa ISO 178
챠피 충격 강도 , +23°C 90 / 97 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 13 / 16 kJ/m² ISO 179/1eA
로크웰 경도 R 120 - ISO 2039-2
ASTM 데이터
인장 강도 210 / 135 MPa ASTM D 638
파단시 신율 3 / 5 % ASTM D 638
굴곡 계수 10400 / 6300 MPa ASTM D 790
굴곡 강도 325 / 210 MPa ASTM D 790
로크웰 경도 M 96 / M 75 - ASTM D 785
Taber내마모성 15 mg/1000 cycles ASTM D 1044
아이조드 충격은 노치, 1/8 in 130 / 170 J/m ASTM D 256
열적 특성건조/응축단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 250 / * °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 260 / * °C ISO 75-1/-2
두께 H인 제품의 난연성 HB / * class IEC 60695-11-10
테스트 두께 0.8 / * mm -
Yellow Card 유효한 예 / * - -
ASTM 데이터
UL94 난연성 HB - UL 94
테스트 두께 0.75 mm -
열팽창 계수, 평행 20 E-6/K ASTM D 696
DTUL @ 66 psi 260 °C ASTM D 648
DTUL @ 264 psi 250 °C ASTM D 648
열전도율, 솔리드 0.0432 W/(m K) ASTM C 177
전기적 특성건조/응축단위시험규격
ISO 데이터
부피 저항 1E13 / - Ohm*m IEC 62631-3-1
표면 저항 * / 1E15 Ohm IEC 62631-3-2
전기 압력 33 / - kV/mm IEC 60243-1
CTI 425 / - - IEC 60112
ASTM 데이터
전기 압력, 단기간의 33 / - kV/mm ASTM D 149
부피 저항 1E15 / - Ohm*cm ASTM D 257
기타 특성건조/응축단위시험규격
조건에서의 흡습성 1.7 / * % ISO 62와 유사
밀도 1390 / - kg/m³ ISO 1183
밀도 1390 kg/m³ ASTM D 792
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 80 - 90 °C -
Pre-drying - Time 2 - 3 h -
용융수지온도 275 - 295 °C -
성형온도 75 - 85 °C -
특징
생산 공정
사출 성형
인도 유형
펠렛 (입자,알갱이)
특별 특성
열안정성
응용
자동차의
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.