Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of DuraStar™ MN630 - PCTA - Eastman Chemical Co.

Material Data Center offers the following functions for DuraStar™ MN630:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Durastar datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 광학 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
제품 설명서

DuraStar™ Copolyester MN630 does not contain a mold release. It has excellent appearance and is nearly waterclear.

Its most outstanding feature is its high flow characteristic, with the ability to fill intricate tooling. It is easy to process with minimal drying time and has good toughness and chemical resistance.




Processing/Physical Characteristics값단위시험규격
ASTM 데이터
성형 수축률, 평행 0.003 mm/mm ASTM D 955
기계적 특성값단위시험규격
ASTM 데이터
항복강도 50 MPa ASTM D 638
파단시 강도 43 MPa ASTM D 638
항복변형률 5 % ASTM D 638
파단시 신율 270 % ASTM D 638
굴곡 계수 1900 MPa ASTM D 790
로크웰 경도 R 107 - ASTM D 785
아이조드 충격은 노치, 1/8 in 80 J/m ASTM D 256
아이조드 충격은 노치, Low-Temperature 44 J/m ASTM D 256
온도 -40 °C -
Izod충격강도, 1/8 in N J/m ASTM D 256
열적 특성값단위시험규격
ASTM 데이터
DTUL @ 66 psi 73 °C ASTM D 648
DTUL @ 264 psi 66 °C ASTM D 648
비카트 연화 온도 86 °C ASTM D 1525
광학 특성값단위시험규격
ASTM 데이터
탁도 1 % ASTM D 1003
광선 투겠淅 92 % ASTM D 1003
기타 특성값단위시험규격
물에서의 흡수성, 24hr 0.15 % ASTM D 570
밀도 1190 kg/m³ ASTM D 792
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 70 °C -
Pre-drying - Time 4 h -
용융수지온도 230 - 280 °C -
성형온도 15 - 30 °C -
특징
생산 공정
사출 성형
특별 특성
투명도
특성
Color Stability
내화학성에
General Chemical Resistance, Solvent Resistance, Radiation Resistance
응용
의료
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.