Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of CELANEX® 6500 - PBT-(GF+MD)30 - Celanese

Material Data Center offers the following functions for CELANEX® 6500:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Celanex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - 도표
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics값단위시험규격
ISO 데이터
성형 수축률, 평행 0.2 % ISO 294-4, 2577
성형 수축률, 수직 0.7 % ISO 294-4, 2577
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 9700 MPa ISO 527
파단시 강도 125 MPa ISO 527
파단시 신율 2.2 % ISO 527
챠피 충격 강도 , +23°C 30 kJ/m² ISO 179/1eU
챠피 충격 강도, -30°C 30 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 7.1 kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 6.4 kJ/m² ISO 179/1eA
쇼어 D 경도 85 - ISO 7619-1
열적 특성값단위시험규격
ISO 데이터
녹는점, 10°C/min 225 °C ISO 11357-1/-3
유리 전이 온도, 10 °C/min 54 °C ISO 11357-1/-2
하중하에서의 변형온도, 1.80 MPa 202 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 223 °C ISO 75-1/-2
선형 열팽창 계수, 평행 28 E-6/K ISO 11359-1/-2
선형 열팽창 계수, 수직 85 E-6/K ISO 11359-1/-2
전기적 특성값단위시험규격
ISO 데이터
상대 유전율, 100Hz 3.5 - IEC 62631-2-1
상대 유전뮬, 1MHz 3.8 - IEC 62631-2-1
소산 인자, 1MHz 400 E-4 IEC 62631-2-1
부피 저항 >1E13 Ohm*m IEC 62631-3-1
표면 저항 >1E15 Ohm IEC 62631-3-2
전기 압력 22 kV/mm IEC 60243-1
기타 특성값단위시험규격
물에서의 흡수성 0.4 % ISO 62와 유사
조건에서의 흡습성 0.19 % ISO 62와 유사
밀도 1550 kg/m³ ISO 1183
도표
응력-신율 , CELANEX® 6500, PBT-(GF+MD)30, Celanese
시컨트탄성율-신율 , CELANEX® 6500, PBT-(GF+MD)30, Celanese
특징
생산 공정
사출 성형
인도 유형
펠렛 (입자,알갱이)
부가물
윤활제
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
기타 정보
사E성
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30°F (-34°C) at 250°F (121°C) for minimum 4 hours.
Rear Temperature 450-480 (230-250) deg F (deg C)
Center Temperature 460-490(235-255) deg F (deg C)
Front Temperature 470-500 (240-260) deg F (deg C)
Nozzle Temperature 480-510 (250-265) deg F (deg C)
Melt Temperature 460-510 (235-265) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast

Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.