Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of CELANEX® 6500 - PBT-(GF+MD)30 - Celanese

Material Data Center offers the following functions for CELANEX® 6500:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Celanex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Funzioni
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Ritiro di stampaggio, parallelo 0.2 % ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare 0.7 % ISO 294-4, 2577
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Modulo a trazione 9700 MPa ISO 527
Carico unitario a rottura 125 MPa ISO 527
Deformazione a rottura 2.2 % ISO 527
Resistenza all'urto Charpy, +23°C 30 kJ/m² ISO 179/1eU
Resistenza all'urto Charpy, -30°C 30 kJ/m² ISO 179/1eU
Resistenzia all'urto Charpy con intaglio, +23°C 7.1 kJ/m² ISO 179/1eA
Resistenzia all'urto Charpy con intaglio, -30°C 6.4 kJ/m² ISO 179/1eA
Durezza Shore D 85 - ISO 7619-1
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 225 °C ISO 11357-1/-3
Temperatura di transizione vetrosa, 10°C/min 54 °C ISO 11357-1/-2
Temp.di inflessione sotto carico, 1.80 MPa 202 °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 223 °C ISO 75-1/-2
Coeff.di dilatazione termica lin., parallelo 28 E-6/K ISO 11359-1/-2
Coeff.di dilatazione termica lin., perpend. 85 E-6/K ISO 11359-1/-2
Proprietà ElettricheValoreUnitáNorma del test
ISO Data
Costante dielettrica relativa, 100Hz 3.5 - IEC 62631-2-1
Costante dielettrica relativa, 1MHz 3.8 - IEC 62631-2-1
Fattore di dissipazione, 1MHz 400 E-4 IEC 62631-2-1
Resistività volumica >1E13 Ohm*m IEC 62631-3-1
Resistività superficiale >1E15 Ohm IEC 62631-3-2
Rigidità dielettrica 22 kV/mm IEC 60243-1
Altre ProprietàValoreUnitáNorma del test
Assorbimento d'acqua 0.4 % Sim. alla ISO 62
Assorbimento d'umidità 0.19 % Sim. alla ISO 62
Massa volumica 1550 kg/m³ ISO 1183
Funzioni
Sforzi-deformazione , CELANEX® 6500, PBT-(GF+MD)30, Celanese
Modulo secante-deformazione , CELANEX® 6500, PBT-(GF+MD)30, Celanese
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet
Additivi
Lubrificanti
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, South and Central America, Near East/Africa
Altre informazioni
Stampaggio ad Iniezione
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30°F (-34°C) at 250°F (121°C) for minimum 4 hours.
Rear Temperature 450-480 (230-250) deg F (deg C)
Center Temperature 460-490(235-255) deg F (deg C)
Front Temperature 470-500 (240-260) deg F (deg C)
Nozzle Temperature 480-510 (250-265) deg F (deg C)
Melt Temperature 460-510 (235-265) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast

Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.