Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of TEREZ® PA 6.6 7750 TD - PA66 - Ter Plastics

Material Data Center offers the following functions for TEREZ® PA 6.6 7750 TD:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Terez datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Proprietà Meccaniche - Proprietà Termiche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Testo del prodotto

Dry impact modified Polyamide 6.6 with good flowability

and good demouldability.

For all kind of moulding parts with increased demand of Impact resistance.



Proprietà Meccanichesecco/condUnitáNorma del test
ISO Data
Modulo a trazione 2500 / 850 MPa ISO 527
Carico unitario a trazione 65 / 40 MPa ISO 527
Deformazione a snervamento 3.5 / 20 % ISO 527
Deformazione a rottura 28 / - % ISO 527
Resistenza all'urto Charpy, +23°C N / - kJ/m² ISO 179/1eU
Resist. urto Charpy con intaglio, +23°C 12 / 20 kJ/m² ISO 179/1eA
Resist. urto Charpy con intaglio, -30°C 5 / - kJ/m² ISO 179/1eA
Proprietà Termichesecco/condUnitáNorma del test
ISO Data
Temp.di inflessione sotto carico, 1.80 MPa 65 / * °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 170 / * °C ISO 75-1/-2
Reaz. al fuoco spess.nom. 1.5mm HB / * class IEC 60695-11-10
Spessore provato 1.6 / * mm -
Altre Proprietàsecco/condUnitáNorma del test
Assorbimento d'acqua 7.3 / * % Sim. alla ISO 62
Assorbimento d'umidità 2 / * % Sim. alla ISO 62
Massa volumica 1120 / - kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 80 °C -
Pre-essiccamento - Tempo 4 - 8 h -
Umidità del Processo ≤0.1 % -
Temperatura dello stampo 40 - 80 °C -
Temperatura - Zona di Alimentazione 60 - 80 °C -
Zona 1 260 - 290 °C -
Temperatura dell ugello 270 - 300 °C -
Tempo di residenza, massimo 8 min -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet
Additivi
Agente di distacco
Caratteristiche speciali
Alto urto o modificato all'urto
Disponibilità geografica
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.