Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Tefabloc™ TO 823 80A - TPS - Mitsubishi Chemical Performance Polymers

Material Data Center offers the following functions for Tefabloc™ TO 823 80A:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Tefabloc datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di Fluiditá, MFI 18 g/10min ISO 1133
Temperatura 190 °C -
Carico 5 kg -
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Resistenza a trazione 6.7 MPa ISO 37
Deformazione a rottura 480 % ISO 37
Deformazione residua dopo compressione a 70°C, 24h 45 % ISO 815
Deformazione residua dopo compressione a 100°C, 24h 48 % ISO 815
Resistenza alla lacerazione 36 kN/m ISO 34-1
Durezza Shore A 80 - ISO 7619-1
Other Standards[S]
Carico Unitario al 100% di allungamento 4.3 MPa ISO 37
Resistenza all'abrasione 110 mm³ DIN 53516
S: These properties are reported by the producer according standards that are different to our defaults.
Altre ProprietàValoreUnitáNorma del test
Massa volumica 1030 kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 60 °C -
Pre-essiccamento - Tempo 4 h -
Temperatura di fusione 250 °C -
Temperatura dello stampo 20 - 60 °C -
Zona 1 190 - 220 °C -
Temperatura dell ugello 220 °C -
Velocità di Rotazione della Vite 50 - 80 rpm -
Velocità di iniezione 40 - 100 mm/s -
Pressione di Iniezione 10 - 25 MPa -
Pressione di chiusura 10 - 15 MPa -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet
Caratteristiche speciali
Estab. agli U.V. o per applicaz.in esterni, Opaque
Caratteristiche
Basso odore
Resistenza Chimica
Resistenza agli alcali
Certifications
Contatto con gli alimenti
Applicazioni
Automotive
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.