Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LUVOCOM 1105-8356 - PEEK - LEHVOSS Group

Material Data Center offers the following functions for LUVOCOM 1105-8356:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Luvocom datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 22 cm³/10min ISO 1133
Temperatura 380 °C -
Carico 10 kg -
Ritiro di stampaggio, parallelo 1.3 % ISO 294-4, 2577
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Modulo a trazione 4000 MPa ISO 527
Resistenza a trazione 95 MPa ISO 527
Modulo a flessione, 23°C 3500 MPa ISO 178
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temp.di inflessione sotto carico, 1.80 MPa 150 °C ISO 75-1/-2
Reazione al fuoco a spessore h V-0 class IEC 60695-11-10
Proprietà ElettricheValoreUnitáNorma del test
ISO Data
Resistività superficiale 1E13 Ohm IEC 62631-3-2
Altre ProprietàValoreUnitáNorma del test
Massa volumica 1310 kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 150 °C -
Pre-essiccamento - Tempo 3 - 6 h -
Umidità del Processo ≤0.05 % -
Temperatura di fusione 390 °C -
Temperatura dello stampo 170 - 200 °C -
Zona 1 360 - 370 °C -
Zona 2 380 - 390 °C -
Zona 3 390 - 400 °C -
Temperatura dell ugello 360 - 380 °C -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Colore naturale
Caratteristiche speciali
Ritardante di fiamma
Resistenza Chimica
Resistenza chimica generale
Applicazioni
Aereo e aerospaziale, Automotive, Medicale
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.