Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of CELANEX® 5200-2 - PBT-GF15 - Celanese

Material Data Center offers the following functions for CELANEX® 5200-2:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Celanex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà
Any use of this information falls under the rules of our disclaimer.
Testo del prodotto
Celanex 5200-2 is a 15% fiberglass reinforced polyester with improved surface finish. Celanex 5200-2 contains an internal lubricant.

Flammability at thickness h (0.75 mm)HB-
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 38 cm³/10min ISO 1133
Temperatura 265 °C -
Carico 2.16 kg -
Ritiro di stampaggio, parallelo 0.5 % ISO 294-4, 2577
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Modulo a trazione 6000 MPa ISO 527
Carico unitario a rottura 120 MPa ISO 527
Deformazione a rottura 3 % ISO 527
Resistenza all'urto Charpy, +23°C 35 kJ/m² ISO 179/1eU
Resistenza all'urto Charpy, -30°C 35 kJ/m² ISO 179/1eU
Resistenzia all'urto Charpy con intaglio, +23°C 8 kJ/m² ISO 179/1eA
Resistenzia all'urto Charpy con intaglio, -30°C 8 kJ/m² ISO 179/1eA
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 250 °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 1.80 MPa 190 °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 215 °C ISO 75-1/-2
Temp.di rammollimento Vicat, B 210 °C ISO 306
Coeff.di dilatazione termica lin., parallelo 35 E-6/K ISO 11359-1/-2
Reazione al fuoco a spessore h HB class IEC 60695-11-10
Spessore provato 0.8 mm -
Indice di ossigeno 20 % ISO 4589-1/-2
Proprietà ElettricheValoreUnitáNorma del test
ISO Data
Costante dielettrica relativa, 100Hz 4.3 - IEC 62631-2-1
Costante dielettrica relativa, 1MHz 4 - IEC 62631-2-1
Fattore di dissipazione, 100Hz 11 E-4 IEC 62631-2-1
Fattore di dissipazione, 1MHz 190 E-4 IEC 62631-2-1
Resistività volumica >1E13 Ohm*m IEC 62631-3-1
Resistività superficiale >1E15 Ohm IEC 62631-3-2
Rigidità dielettrica 28 kV/mm IEC 60243-1
Altre ProprietàValoreUnitáNorma del test
Assorbimento d'acqua 0.45 % Sim. alla ISO 62
Assorbimento d'umidità 0.2 % Sim. alla ISO 62
Massa volumica 1410 kg/m³ ISO 1183
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet
Additivi
Lubrificanti
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.