Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RTP 2107 - PEI-GF40 - RTP Company

Material Data Center offers the following functions for RTP 2107:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other RTP datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ASTM Data
Retrait au moulage , parallèle 0.001 mm/mm ASTM D 955
Propriétés mécaniquesValeurUnitéNorme du test
ASTM Data
Module en traction 13440 MPa ASTM D 638
Module de traction 190 MPa ASTM D 638
Résistance de compression 169 MPa ASTM D 695
Module de flexion 13100 MPa ASTM D 790
Résistance à la flexion 269 MPa ASTM D 790
Dureté Rockwell R 123 - ASTM D 785
Izod choc avec entaille, 1/8 in 101 J/m ASTM D 256
Propriétés thermiquesValeurUnitéNorme du test
ASTM Data
UL 94 inflammabilité V-0 - UL 94
Épaisseur testée 1.59 mm -
DTUL à 66 psi 210 °C ASTM D 648
DTUL à 264 psi 207 °C ASTM D 648
Propriétés électriquesValeurUnitéNorme du test
ASTM Data
Rigidité diélectrique, peu de temps 19.7 kV/mm ASTM D 149
Facteur de dissipation diélectrique, 1 MHz 0.005 - ASTM D 150
Constante diélectrique, 1 MHz 4 - ASTM D 150
Propriétés diversesValeurUnitéNorme du test
Absorption d’eau, 24hr 0.18 % ASTM D 570
Densité 1590 kg/m³ ASTM D 792
Moisture Content 0.04 % -
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 149 °C -
Pré-séchage - temps 4 h -
Température de la matière fondue 354 - 399 °C -
Température du moule 135 - 177 °C -
Pressions d'injection 82.7 - 124 MPa -
Caractéristiques
Transformation
Moulage par injection
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.