Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of KRALASTIC™ AN-466 - ABS - Nippon A&L Inc.

Material Data Center offers the following functions for KRALASTIC™ AN-466:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Kralastic datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caractéristiques des transformations/physiques - Propriétés mécaniques - Propriétés thermiques - Propriétés diverses - Recommandations pour la transformation Moulage par injection
Any use of this information falls under the rules of our disclaimer.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ISO Data
Indice de fluidité à chaud en volume, MVR 5.5 cm³/10min ISO 1133
Température 200 °C -
Charge 5 kg -
Other Standards[S]
Retrait au moulage, parallèle 0.5 % Producer Method
S: These properties are reported by the producer according standards that are different to our defaults.
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Contrainte d'écoulement 46 MPa ISO 527
Module de flexion, 23°C 2650 MPa ISO 178
Résistance à la flexion 75 MPa ISO 178
Résistance au choc Charpy (entaillé), +23°C 12 kJ/m² ISO 179/1eA
Dureté Rockwell R 115 - ISO 2039-2
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fléchissement s/chrg, 1.80 MPa 78 °C ISO 75-1/-2
Coeffic. de dilatation therm. linéique, parallèle 78 E-6/K ISO 11359-1/-2
Inflammabilité ep. nom. 1.5 mm V-2 class IEC 60695-11-10
Epaisseur de l'éprouvette 1.5 mm -
Propriétés diversesValeurUnitéNorme du test
Masse volumique 1100 kg/m³ ISO 1183
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 75 - 85 °C -
Pré-séchage - temps 3 - 6 h -
Température de la matière fondue 180 - 210 °C -
Température du moule 40 - 60 °C -
Caractéristiques
Transformation
Moulage par injection
Propriétés spéciales
Ignifugé
Disponibilité régionale
Asia Pacific
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.