Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Bakelite® PF 1110 - PF-(GF+X) - Bakelite Synthetics

Material Data Center offers the following functions for Bakelite® PF 1110:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Bakelite datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caractéristiques des transformations/physiques - Propriétés mécaniques - Propriétés thermiques - Propriétés électriques - Propriétés diverses - Préparation et conditionnement des éprouvettes
Any use of this information falls under the rules of our disclaimer.
Informations produit

Product description:

Phenolic moulding compound, inorganically filled, glass fibre reinforced, high heat resistance, very low coefficient of thermal expansion, highest resistance to pressure, high dimensional stability.


Application areas:

Thermally and mechanically highly stressed parts in automotive UTH; e.g. large format parts, engine attachments, insulating flanges, brake pistons, impellers, pulleys and pump parts.


Property Name Value Unit Standard No.
Apparent density (moulding compound) 0,8
 g/cm³ ISO 60
Moulding shrinkage (injection moulding, longitudinal)  0.15 % ISO 2577
Post shrinkage (injection moulding, 168h/110°C) 0.03 % ISO 2577
Tensile strength (5mm/min) 120 MPa ISO 527-1/2
Compr. strength (test spec. flat tested) 275 MPa ISO 604
Flexural strength (2mm/min) 240 MPa ISO 178
Flexural modulus 25000 MPa ISO 178
Water absorption (24h/23°C) 7 mg similar to ISO 62


Additional characteristics: low shrinkage/good dimensional stability, resistant to high temperature



Preparation of Test Specimens of Thermosetting Moulding Compound

  • Compression to ISO 295
  • Injection to ISO 10724


Storage capability
2 years (relative humidity of 50-60% and maximum storage temperature of approximately 20°C)

Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ISO Data
Retrait au moulage, parallèle 0.1 % ISO 294-4, 2577
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Module en traction 26000 MPa ISO 527
Résistance au choc Charpy, +23°C 13 kJ/m² ISO 179/1eU
Résistance au choc Charpy (entaillé), +23°C 4 kJ/m² ISO 179/1eA
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fléchissement s/chrg, 8.00 MPa 195 °C ISO 75-1/-2
Inflammabilité pr. épaisseur h V-0 class IEC 60695-11-10
Epaisseur de l'éprouvette 0.8 mm -
Yellow Card disponible oui - -
Propriétés électriquesValeurUnitéNorme du test
ISO Data
Permittivité relative, 100Hz 6.5 - IEC 62631-2-1
Facteur de pertes, 100Hz 0.05 E-4 IEC 62631-2-1
Résistivité transversale 1E10 Ohm*m IEC 62631-3-1
Résistivité superficielle 1E11 Ohm IEC 62631-3-2
Rigidité diélectrique 27.5 kV/mm IEC 60243-1
Indice de résistance au cheminement 225 - IEC 60112
Propriétés diversesValeurUnitéNorme du test
Masse volumique 2050 kg/m³ ISO 1183
Préparation et conditionnement des éprouvettesValeurUnitéNorme du test
ISO Data
Injection, temp. de la matière plastif. 115 °C ISO 10724
Injection, vitesse d'injection 170 mm/s ISO 10724
Injection, pression de maintien 100 MPa ISO 10724
Injection, durée de recuit 25 min ISO 10724
Compression, température du moule 160 °C ISO 295
Compression, temps de recuit 1 min ISO 295
Caractéristiques
Transformation
Moulage par injection, Moulage par transfert
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique
Autres informations
Moulages par injection
VERARBEITUNG 
Temperature of material: 80 - 100 °C
Mould temperature: 160 - 190 °C
Curing time: 10-20 sec
 
Further Information:
Barrel temperature
  - Feed zone: 60-75 °C
  - Nozzle zone: 80-100 °C
Cavity moulding pressure: >15 MPa
Back pressure: 0.5-2 MPa
Holding pressure: 60% of injection pressure
Moulage par compression
PROCESSING
Mould temperature:160-190°C
Curing time:20-40sec
Cavity moulding pressure: >15MPa
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.