Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Wellamid® 22LHI6 XE-N - PA66 - Wellman Advanced Materials

Material Data Center offers the following functions for Wellamid® 22LHI6 XE-N:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Wellamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Contracción posterior al moldeo, paralelo 1.9 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 2.0 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de tracción 60 MPa ISO 527
Módulo de flexión, 23°C 2100 MPa ISO 178
Resistencia a la flexión 75 MPa ISO 178
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 260 °C ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa 60 °C ISO 75-1/-2
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1110 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 80 °C -
Tiempo de pre-secado 2 - 4 h -
Humedad de procesamiento ≤0.15 % -
Temperatura del molde 71 - 93 °C -
Zona 1 260 - 293 °C -
Zona 2 260 - 293 °C -
Zona 3 266 - 293 °C -
Temperatura de boquilla 254 - 293 °C -
Velocidad de giro de husillo 30 - 120 rpm -
Presión de inyección 34 - 138 MPa -
Contrapresión 0.34 - 1.03 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Alto impacto o modificado al impacto
Applicaciones
Automotriz
Disponibilidad regional
Norteamérica
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.