Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VICTREX® PEEK 150G - PEEK - Victrex plc

Material Data Center offers the following functions for VICTREX® PEEK 150G:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Victrex PEEK datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Contracción posterior al moldeo, paralelo 1.0 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 1.3 % ISO 294-4, 2577
Conductibilidad termica de fusión 0.29 W/(m K) -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 4100 MPa ISO 527
Esfuerzo de fluencia 105 MPa ISO 527
Alargamiento a rotura 30 % ISO 527
Módulo de flexión, 23°C 3900 MPa ISO 178
Resistencia al impacto Charpy, +23°C N kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 4.2 kJ/m² ISO 179/1eA
Resistencia al impacto Izod, +23°C N kJ/m² ISO 180/1U
Resistencia al impacto Izod con entalla, +23°C 5 kJ/m² ISO 180/1A
Dureza Shore D 85 - ISO 7619-1
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 343 °C ISO 11357-1/-3
Temp. de transición vítrea, 10°C/min 143 °C ISO 11357-1/-2
Estabilidad al calor, 1.80 MPa 156 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 50 E-6/K ISO 11359-1/-2
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (1) 2 mm -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Factor de pérdidas dieléctricas, 1MHz 40 E-4 IEC 62631-2-1
Resistividad volumétrica específica 1E14 Ohm*m IEC 62631-3-1
Resistencia dieléctrica 23 kV/mm IEC 60243-1
Indice comparativo de linea de fuga 150 - IEC 60112
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 0.45 % Sim. to ISO 62
Densidad 1300 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 120 - 150 °C -
Tiempo de pre-secado 3 - 5 h -
Humedad de procesamiento ≤0.02 % -
Temperatura del molde 160 - 200 °C -
Temperatura - zona de alimentación ≤100 °C -
Zona 1 350 °C -
Zona 2 355 °C -
Zona 3 355 °C -
Zona 4 360 °C -
Temperatura de boquilla 365 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Sémola, Color natural
Características especiales
Esterilizable
Características
Ductil
Resistencia quimica
Resistencia química general
Certifications
Contacto con alimentos, Aprobado por el FDA 21 CFR
Applicaciones
Médico
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.