Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin AUT230 - Europe - PEI - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for ULTEM™ Resin AUT230 - Europe:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Texto del producto
Transparent polyetherimide (Tg 247C). Very low outgassing and plateout, for automotive lighting applications where highly metallized, reflective surfaces are required. Haze onset temperature of 230C (SABIC Innovative Plastics method)
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 8 cm³/10min ISO 1133
Temperatura 360 °C -
Carga 5 kg -
ASTM Data
Índice de fluidez, MFI 15.5 g/10min ASTM D 1238
Temperatura 367 °C -
Carga 6.6 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 3110 MPa ISO 527
Esfuerzo de fluencia 95 MPa ISO 527
Alarg. en límite elástico 8.5 % ISO 527
Resistencia a la tracción 78 MPa ISO 527
Alargamiento a rotura 16.8 % ISO 527
Modulo de Flexión 3080 MPa ISO 178
Izod impact strength, +23°C, 4mm N kJ/m² ISO 180/1U
Izod impact strength, -30°C, 4mm N kJ/m² ISO 180/1U
Res. impacto Izod c/entalla, +23°C, 4mm 4 kJ/m² ISO 180/1A
Res. impacto Izod c/entalla, -30°C, 4mm 5 kJ/m² ISO 180/1A
ASTM Data
Módulo de tracción 3510 MPa ASTM D 638
Esfuerzo de fluencia a tracción 96 MPa ASTM D 638
Esfuerzo de fractura a tracción 96 MPa ASTM D 638
Alargamiento a la fluencia 6 % ASTM D 638
Alargamiento a la rotura 25 % ASTM D 638
Módulo de flexión 3170 MPa ASTM D 790
Resistencia al impacto Izod con entalla, 1/8 in 69 J/m ASTM D 256
Resistencia al impacto Izod con entalla, baja temperatura 74 J/m ASTM D 256
Temperatura -30 °C -
Resistencia al impacto Izod, 1/8 in N J/m ASTM D 256
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 228 °C ISO 75-1/-2
Temp. reblandecimiento Vicat, B 242 °C ISO 306
Temp. reblandecimiento Vicat, 120°C/h 50N 238 °C ISO 306
ASTM Data
Estabilidad al calor @ 264 psi 217 °C ASTM D 648
Temperatura Vicat 242 °C ASTM D 1525
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 1.75 % Sim. to ISO 62
Absorción de humedad 0.6 % Sim. to ISO 62
Densidad 1300 kg/m³ ISO 1183
Densidad 1300 kg/m³ ASTM D 792
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 150 °C -
Tiempo de pre-secado 4 - 6 h -
Humedad de procesamiento ≤0.02 % -
Temperatura de la masa 380 - 405 °C -
Temperatura del molde 135 - 165 °C -
Zona 1 360 - 380 °C -
Zona 2 370 - 395 °C -
Zona 3 380 - 405 °C -
Velocidad de giro de husillo 40 - 70 rpm -
Contrapresión 0.3 - 0.7 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Transparente
Applicaciones
Automotriz
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.