Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Makrolon® M402 LF - PC - Covestro Deutschland AG

Material Data Center offers the following functions for Makrolon® M402 LF:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Makrolon datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Texto del producto
  • polycarbonate
  • MVR (300 °C/1.2 kg) 19 cm³/10 min
  • low viscosity
  • improved friction characteristics
  • biocompatible according to many ISO 10993-1 test requirements
  • suitable for medical devices
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 19 cm³/10min ISO 1133
Temperatura 300 °C -
Carga 1.2 kg -
Contracción posterior al moldeo, paralelo 0.7 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 0.7 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 2150 MPa ISO 527
Esfuerzo de fluencia 60 MPa ISO 527
Alarg. nominal a rotura >50 % ISO 527
Resistencia al impacto Izod con entalla, +23°C 60 kJ/m² ISO 180/1A
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temp. reblandecimiento Vicat, B 144 °C ISO 306
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1200 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 120 °C -
Tiempo de pre-secado 4 h -
Humedad de procesamiento ≤0.02 % -
Temperatura de la masa 280 - 320 °C -
Temperatura del molde 70 - 110 °C -
Zona 1 250 - 270 °C -
Zona 2 270 - 290 °C -
Zona 3 285 - 305 °C -
Temperatura de boquilla 270 - 305 °C -
Contrapresión 10 - 20 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Opaque
Características
Grado tribológico
Certifications
Grado médico, Biocompatibility ISO 10993
Applicaciones
Médico
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, Próximo Oriente/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.