Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LUVOCOM 1105/XCF/15 - PEEK-CF - LEHVOSS Group

Material Data Center offers the following functions for LUVOCOM 1105/XCF/15:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Luvocom datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Contracción posterior al moldeo, paralelo 0.2 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 18000 MPa ISO 527
Esfuerzo de tracción 255 MPa ISO 527
Módulo de flexión, 23°C 15000 MPa ISO 178
Resistencia al impacto Charpy, +23°C 65 kJ/m² ISO 179/1eU
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Resistividad superficial específica 1000000 Ohm IEC 62631-3-2
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1350 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 150 °C -
Tiempo de pre-secado 3 - 6 h -
Humedad de procesamiento ≤0.05 % -
Temperatura de la masa 390 °C -
Temperatura del molde 170 - 200 °C -
Zona 1 360 - 370 °C -
Zona 2 380 - 390 °C -
Zona 3 390 - 400 °C -
Temperatura de boquilla 360 - 380 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Negro
Características especiales
Conductividad eléctrica aumentada, Resistencia mejorada al fuego
Resistencia quimica
Resistencia química general, Estabilidad hidrolitica
Applicaciones
Avión y aeroespacial, Automotriz, Médico
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.