Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LUMID GP2330A(W) - PA6-GF33 - LG Chem

Material Data Center offers the following functions for LUMID GP2330A(W):
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Lumid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ASTM Data
Contracción posterior al moldeo, paralelo 0.0065 mm/mm ASTM D 955
Propiedades mecánicasValorUnidadesMétodo de ensayo
ASTM Data
Esfuerzo de fractura a tracción 186 MPa ASTM D 638
Alargamiento a la rotura 3 % ASTM D 638
Módulo de flexión 8825 MPa ASTM D 790
Resistencia a la flexión 270 MPa ASTM D 790
Dureza Rockwell R 121 - ASTM D 785
Resistencia al impacto Izod con entalla, 1/8 in 123 J/m ASTM D 256
Propiedades térmicasValorUnidadesMétodo de ensayo
ASTM Data
Combustibilidad UL 94 HB - UL 94
Espesores de probeta 0.75 mm -
Coeficiente de dilatación térmica, long. 35 E-6/K ASTM D 696
Estabilidad al calor @ 264 psi 210 °C ASTM D 648
Temperatura de fusión 220 °C ASTM D 3418
Propiedades eléctricasValorUnidadesMétodo de ensayo
ASTM Data
Resistencia dieléctrica, tiempo corto 20 kV/mm ASTM D 149
Constante dieléctrica, 1 MHz 3.5 - ASTM D 150
Resistividad volumétrica 1E17 Ohm*cm ASTM D 257
Resistencia al arco 130 s ASTM D 495
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua, 24hr 1.1 % ASTM D 570
Densidad 1370 kg/m³ ASTM D 792
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 80 - 100 °C -
Tiempo de pre-secado 4 - 5 h -
Temperatura de la masa 260 - 290 °C -
Temperatura del molde 80 - 100 °C -
Zona 1 250 - 270 °C -
Zona 2 260 - 285 °C -
Zona 3 260 - 290 °C -
Temperatura de boquilla 260 - 290 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Applicaciones
Automotriz, Electrica, Uso general
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.