Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of HOSTAFORM® MT®12U01 ECO-B - POM - Celanese

Check here, which other Hostaform datasheets, application examples or technical articles are available in Material Data Center

Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Funciones

Any use of this information falls under the rules of our disclaimer.

Caracteristicas de procesamiento y fisicas	Valor	Unidades	Método de ensayo
ISO Data
Indice de fluidez volumétrico, MVR	12	cm³/10min	ISO 1133
Temperatura	190	°C	-
Carga	2.16	kg	-
Contracción posterior al moldeo, paralelo	2.0	%	ISO 294-4, 2577
Contracción posterior al moldeo, normal	1.8	%	ISO 294-4, 2577

Propiedades mecánicas	Valor	Unidades	Método de ensayo
ISO Data
Módulo de tracción	2900	MPa	ISO 527
Esfuerzo de fluencia	65	MPa	ISO 527
Alarg. en límite elástico	9	%	ISO 527
Alarg. nominal a rotura	25	%	ISO 527
Resistencia al impacto Charpy, +23°C	200	kJ/m²	ISO 179/1eU
Resistencia al impacto Charpy, -30°C	200	kJ/m²	ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C	6	kJ/m²	ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C	6	kJ/m²	ISO 179/1eA

Propiedades térmicas	Valor	Unidades	Método de ensayo
ISO Data
Temperatura de fusión, 10°C/min	166	°C	ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa	106	°C	ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo	110	E-6/K	ISO 11359-1/-2

Otras propiedades	Valor	Unidades	Método de ensayo
Absorción de agua	0.65	%	Sim. to ISO 62
Absorción de humedad	0.2	%	Sim. to ISO 62
Densidad	1410	kg/m³	ISO 1183

Funciones

Características

Procesamiento y forma de entrega

Moldeo por inyección

Forma de suministro

Sémola

Aditivos

Desmoldeante

Características

Copolímero

Certifications

Aprobado por el FDA 21 CFR, Grado médico, Biocompatibility ISO 10993, USP Class VI, Drug Master File, Device Master File

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.