Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of FORTRON® 1342L4 - PPS-GX40 - Celanese

Material Data Center offers the following functions for FORTRON® 1342L4:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Fortron datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Texto del producto
Fortron 1342L4 is a low wear glass filled grade, ideally suited for bearings, gears and other sliding friction/wear applications.


Flammability @1.6mm nom. thickn.V-0-
Flammability at thickness h (0.75 mm)V-0-
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Contracción posterior al moldeo, paralelo 0.2 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 0.5 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 14400 MPa ISO 527
Resistencia a la tracción 165 MPa ISO 527
Alargamiento a rotura 1.6 % ISO 527
Resistencia al impacto Charpy, +23°C 44 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 8.5 kJ/m² ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C 8.5 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 280 °C ISO 11357-1/-3
Temp. de transición vítrea, 10°C/min 90 °C ISO 11357-1/-2
Estabilidad al calor, 1.80 MPa 270 °C ISO 75-1/-2
Estabilidad al calor, 8.00 MPa 215 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 22 E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 40 E-6/K ISO 11359-1/-2
Combustibilidad a 1.5mm esp. nom. V-0 class IEC 60695-11-10
Espesores de probeta 1.5 mm -
Combustibilidad a espesor h V-0 class IEC 60695-11-10
Espesores de probeta 0.8 mm -
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 0.02 % Sim. to ISO 62
Densidad 1690 kg/m³ ISO 1183
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Sémola
Aditivos
Desmoldeante
Características
Grado tribológico
Disponibilidad regional
Norteamérica, Europa, América del Sur y Centroaméric, Próximo Oriente/Africa
Demás información
Moldeo por inyección
Predrying in a dehumidified air dryer at 130 - 140 degC/3-4 hours is recommended.
On injection molding machines with 15-25 D long three-section screws, as are usual in the trade, the FORTRON is processable. A shut-off nozzle is preferred to a free-flow nozzle.

Melt temperature 320-340 degC
Mold wall temperature at least 140 degC

A medium injection rate is normally preferred. All mold cavities must be effectively vented.
Tool temperature of at least 135 degC is recommended for parts to achieve maximum crystallizable potential.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.