Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of ElectriPlast® EP-SS/66 - PA66-MEF(x) - ElectriPlast
unit conversion, PDF datasheet print, comparison with other plastics
Check here, which other ElectriPlast datasheets, application examples or technical articles are available in Material Data Center
Propiedades mecánicas | Valor | Unidades | Método de ensayo | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ASTM Data | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Módulo de tracción | 5806 | MPa | ASTM D 638 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Esfuerzo de fractura a tracción | 84.4 | MPa | ASTM D 638 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Alargamiento a la rotura | 2.8 | % | ASTM D 638 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Módulo de flexión | 5369 | MPa | ASTM D 790 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistencia a la flexión | 141 | MPa | ASTM D 790 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistencia al impacto Izod con entalla, 1/8 in | 53.4 | J/m | ASTM D 256 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistencia al impacto Izod, 1/8 in | 374 | J/m | ASTM D 256 |
Propiedades térmicas | Valor | Unidades | Método de ensayo | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ASTM Data | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Combustibilidad UL 94 | HB | - | UL 94 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Estabilidad al calor @ 264 psi | 98.9 | °C | ASTM D 648 |
Propiedades eléctricas | Valor | Unidades | Método de ensayo | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ASTM Data | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistividad volumétrica | 5.67 | Ohm*cm | ASTM D 257 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Other Standards[S] | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistividad superficial | 1.73 | Ohm | ESD STM 11.11 |
S: | These properties are reported by the producer according standards that are different to our defaults. |
Otras propiedades | Valor | Unidades | Método de ensayo |
Densidad | 1490 | kg/m³ | ASTM D 792 |
Recomendación para procesamiento Moldeo por inyección | Valor | Unidades | Método de ensayo |
Temperatura de pre-secado | 82.2 | °C | - |
Tiempo de pre-secado | 4 | h | - |
Zona 1 | 282 | °C | - |
Zona 2 | 277 | °C | - |
Zona 3 | 288 | °C | - |
Temperatura de boquilla | 288 | °C | - |
Velocidad de giro de husillo | 50 | rpm | - |
Velocidad de inyección | 25.4 | mm/s | - |
Presión de inyección | 3.45 | MPa | - |
Contrapresión | 0.517 | MPa | - |
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.