Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Dynaflex™ D3226-1000-03 - TPE - Avient Corporation

Material Data Center offers the following functions for Dynaflex™ D3226-1000-03:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Dynaflex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ASTM Data
Índice de fluidez, MFI 26 g/10min ASTM D 1238
Temperatura 190 °C -
Carga 2.16 kg -
Contracción posterior al moldeo, paralelo 0.004 mm/mm ASTM D 955
Propiedades mecánicasValorUnidadesMétodo de ensayo
ASTM Data
Módulo en 100% alargamiento 2.96 MPa ASTM D 412
Dureza A Shore 40 - ASTM D 2240
Resistencia al desgarro 15.8 kN/m ASTM D 624
Compresión residual, 22 hr @ 73 °F 15 % ASTM D 395
Esfuerzo de fractura a tracción 3.59 MPa ASTM D 412
Alargamiento a la rotura 380 % ASTM D 412
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 990 kg/m³ ASTM D 792
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura del molde 21.1 - 32.2 °C -
Zona 1 154 - 193 °C -
Zona 2 160 - 199 °C -
Zona 3 166 - 204 °C -
Temperatura de boquilla 166 - 204 °C -
Velocidad de giro de husillo 25 - 75 rpm -
Velocidad de inyección 25.4 - 127 mm/s -
Contrapresión 0.345 - 1.03 MPa -
Presión de mantenimiento 0.965 - 2.9 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección, Otros tipos de extrusión, Moldeo por soplado, Termoconformación
Forma de suministro
Sémola, Color natural
Características
Resistencia del fundido, Textura suave
Applicaciones
Uso general
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.