Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Desmopan 9380A - TPU - Covestro Deutschland AG

Check here, which other Desmopan datasheets, application examples or technical articles are available in Material Data Center

Propiedades mecánicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección - Funciones

Any use of this information falls under the rules of our disclaimer.

Texto del producto

• Extrusion- and injection molding grade
• very good hydrolysis and microbial resistance
• good low-temperature flexibility
• complies with VDE 0282-10
  Application:
• Cable sheathings
• Hoses, non-reinforced

Propiedades mecánicas	Valor	Unidades	Método de ensayo
ISO Data
Tensión a 10% alargamiento	1.5	MPa	ISO 527
Tensión a 100% alargamiento	5.3	MPa	ISO 527
Tensión a 300% alargamiento	9	MPa	ISO 527
Resistencia a la tracción TPE	43	MPa	ISO 527
Alargamiento a rotura TPE	>300	%	ISO 527
Deformación permanente por compresión a 70°C, 24h	40	%	ISO 815
Resistencia al desgarro	50	kN/m	ISO 34-1
Resistencia a la abrasión	25	mm³	ISO 4649
Dureza Shore A	80	-	ISO 7619-1
Dureza Shore D	31	-	ISO 7619-1

Otras propiedades	Valor	Unidades	Método de ensayo
Densidad	1110	kg/m³	ISO 1183

Recomendación para procesamiento Moldeo por inyección	Valor	Unidades	Método de ensayo
Temperatura de pre-secado	80	°C	-
Tiempo de pre-secado	1 - 2	h	-
Humedad de procesamiento	≤0.05	%	-
Temperatura de la masa	200 - 230	°C	-
Temperatura del molde	20 - 40	°C	-

Funciones

Características

Procesamiento y forma de entrega

Moldeo por inyección, Extrusión de perfiles, Extrusión de láminas, Otros tipos de extrusión

Disponibilidad regional

Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa

Demás información

Moldeo por inyección

PREPROCESSING
Max. water content: 0.05 %
Max. drying temperature: 80 °C
Drying time:
Dry air dryer 1-2 h

PROCESSING
Melt temperature: 200-230 °C
Mold temperature: 20-40 °C

Otros tipos de extrusión

 Preprocessing

Max. Water content	≤0.05 %
Drying temperature	70-110 °C
Dry air dryer	1-2 h

 Processing

Melt temperature

195-215 °C

Extrusión de perfiles

 Preprocessing

Max. Water content	≤0.05 %
Drying temperature	70-110 °C
Dry air dryer	1-2 h

 Processing

Melt temperature

180-210 °C

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.