Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of AVALON® 75 ABX - TPU - Huntsman Polymers Corp.

Material Data Center offers the following functions for AVALON® 75 ABX:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Avalon datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propiedades mecánicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Propiedades mecánicasValorUnidadesMétodo de ensayo
Other Standards[S]
Esfuerzo de tracción 25 MPa DIN 53504
Alargamiento a rotura 750 % DIN 53504
Resistencia al desgarro 35 kN/m DIN 53507
Resistencia a la abrasión 50 mm³ DIN 53516
Dureza Shore A 75 - DIN 53505
S: These properties are reported by the producer according standards that are different to our defaults.
Otras propiedadesValorUnidadesMétodo de ensayo
Other Standards[S]
Densidad 1140 kg/m³ DIN 53479
S: These properties are reported by the producer according standards that are different to our defaults.
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 80 - 90 °C -
Tiempo de pre-secado 2 h -
Temperatura del molde 25 - 50 °C -
Temperatura - zona de alimentación 25 - 35 °C -
Zona 1 160 - 180 °C -
Zona 2 165 - 185 °C -
Zona 3 165 - 190 °C -
Temperatura de boquilla 160 - 185 °C -
Velocidad de giro de husillo 20 - 80 rpm -
Presión de inyección 2 - 10 MPa -
Contrapresión 0.03 - 0.3 MPa -
Presión de mantenimiento 1 - 5 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características
Antideslizante, Resistente a rayado
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.