Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ALFATER XL D40I 4FC0010 - TPV - MOCOM Compounds GmbH & Co. KG

Material Data Center offers the following functions for ALFATER XL D40I 4FC0010:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Alfater datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propiedades mecánicas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Texto del producto
Base PolymerThermoplastic Vulcanisate (PP+EPDM)
Colournatural color,bright inherent color,blue
Service Temperaturemax. range (depending on load, geometry, etc.) -40-125 °C
Special Featuresfood contact,compliant EN 71-3,good colorability,good weathering resistance,good chemical resistance,good ozone reistance,good hot air resistance,good hydrolysis resistant,easy flow
Market Segmentpackaging,household goods,food processing industry,toys
Application Areainjection moulded parts
Typical Applicationsseals,sealing lip,handles,protection caps,caps / closures,containers,kitchen ware,2K components
Adhesion toPolypropylene Homopolymer,Polypropylene Copolymer,Polyethylene,Thermoplastic Vulcanisate (PP+EPDM),Thermoplastic Olefin Elastomer,Thermoplastic Elastomer general
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Resistencia al desgarro 74 kN/m ISO 34-1
Dureza Shore D 40 - ISO 7619-1
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 950 kg/m³ ISO 1183
Características
Procesamiento y forma de entrega
Moldeo por inyección
Certifications
Contacto con alimentos
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, Próximo Oriente/Africa
Demás información
Moldeo por inyección
Pre-Drying Conditionsin a dry air (dessiccant) dryer 70-80 °C
for 2-4 h
max. moisture content <0,10 %
Processing Injection Mouldingmelt temperature 195-230 °C
mould temperature 10-70 °C
injection speed middle - high
back pressure (hydraulic) >3 bar
holding pressure 50-70% of injection pressure
Storagedry, protected from light
tightly sealed
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.