Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NOVADURAN 5710N2 - PBT - Mitsubishi Engineering-Plastics Corporation

Material Data Center offers the following functions for NOVADURAN 5710N2:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Novaduran datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Melt volume-flow rate, MVR 7 cm³/10min ISO 1133
Temperature 250 °C -
Load 2.16 kg -
Molding shrinkage, parallel 1.1 % ISO 294-4, 2577
Molding shrinkage, normal 1.1 % ISO 294-4, 2577
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Modulus 2400 MPa ISO 527
Yield stress 60 MPa ISO 527
Yield strain 4 % ISO 527
Strain at break 20 % ISO 527
Flexural modulus, 23°C 2350 MPa ISO 178
Flexural strength 85 MPa ISO 178
Charpy impact strength, +23°C 200 kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 5 kJ/m² ISO 179/1eA
Thermal propertiesValueUnitTest Standard
ISO Data
Melting temperature, 10°C/min 224 °C ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa 115 °C ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa 135 °C ISO 75-1/-2
Burning behav. at 1.5 mm nom. thickn. V-0 class IEC 60695-11-10
Thickness tested 1.5 mm -
Yellow Card available yes - -
Burning behav. at thickness h V-0 class IEC 60695-11-10
Thickness tested 0.8 mm -
Yellow Card available yes - -
Electrical propertiesValueUnitTest Standard
ISO Data
Volume resistivity 1E14 Ohm*m IEC 62631-3-1
Surface resistivity 1E16 Ohm IEC 62631-3-2
Electric strength 21 kV/mm IEC 60243-1
Comparative tracking index 325 - IEC 60112
Other propertiesValueUnitTest Standard
Water absorption 0.08 % Sim. to ISO 62
Density 1360 kg/m³ ISO 1183
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 120 °C -
Pre-drying - Time 5 - 8 h -
Mold temperature 60 - 100 °C -
Zone 1 240 - 260 °C -
Zone 2 240 - 260 °C -
Zone 3 240 - 260 °C -
Nozzle temperature 260 °C -
Screw speed 80 - 120 rpm -
Injection pressure 20 - 150 MPa -
Characteristics
Processing
Injection Molding
Special Characteristics
Flame retardant
Features
Low Warpage
Applications
Automotive, Electrical and Electronical, General Purpose
Regional Availability
North America, Europe, Asia Pacific, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.