Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of Desmopan 9665DU - TPU - Covestro Deutschland AG
unit conversion, PDF datasheet print, comparison with other plastics, parameters for material models, CAE Interfaces
Check here, which other Desmopan datasheets, application examples or technical articles are available in Material Data Center
- Extrusion- and injection molding grade
- with special UV stabilizers
- transparent up to 6 mm wall thickness
- very good hydrolysis and microbial resistance
Application: - Ski boot shells
- Hoses, non-reinforced
- Pneumatic hoses
Mechanical properties | Value | Unit | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Data | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Stress at 10% elongation | 16.5 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Stress at 100% elongation | 29.4 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Stress at 300% elongation | 50 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Stress at break TPE | 57 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Strain at break TPE | >300 | % | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Compression set at 70 °C, 24h | 50 | % | ISO 815 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Tear strength | 170 | kN/m | ISO 34-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Abrasion resistance | 25 | mm³ | ISO 4649 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Shore A hardness | 98 | - | ISO 7619-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Shore D hardness | 65 | - | ISO 7619-1 |
Other properties | Value | Unit | Test Standard |
Density | 1180 | kg/m³ | ISO 1183 |
Processing Recommendation Injection Molding | Value | Unit | Test Standard |
Pre-drying - Temperature | 110 | °C | - |
Pre-drying - Time | 1 - 2 | h | - |
Processing humidity | ≤0.05 | % | - |
Melt temperature | 220 - 240 | °C | - |
Mold temperature | 40 - 60 | °C | - |
Max. water content: 0.05 %
Max. drying temperature: 110 °C
Drying time:
Dry air dryer 1-2 h
PROCESSING
Melt temperature: 210-240 °C
Mold temperature: 40-60 °C
Melt temperature: 205-235 °C
Preprocessing
Max. Water content | ≤0.05 % |
Drying temperature | 70-110 °C |
Dry air dryer | 1-2 h |
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.