Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Promyde® B30 P2 G20 MI - PA6-GF20 - Nurel S.A.

Material Data Center offers the following functions for Promyde® B30 P2 G20 MI:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
加工/物理特性干 / 已调节单位Test Standard
ISO数据
熔体体积流动速度, MVR 30 / * cm³/10min ISO 1133
温度 275 / * °C -
载荷 5 / * kg -
模塑收缩率, 平行 0.3 / * % ISO 294-4, 2577
模塑收缩率, 垂直 0.4 / * % ISO 294-4, 2577
机械性能干 / 已调节单位Test Standard
ISO数据
拉伸模量 5000 / 2900 MPa ISO 527
拉伸强度 110 / 70 MPa ISO 527
断裂伸长率 4.5 / - % ISO 527
弯曲模量, 23°C 4500 / 2800 MPa ISO 178
弯曲强度 145 / 85 MPa ISO 178
简支梁缺口冲击强度, +23°C 16 / 30 kJ/m² ISO 179/1eA
简支梁缺口冲击强度, -30°C 10 / - kJ/m² ISO 179/1eA
热性能干 / 已调节单位Test Standard
ISO数据
熔融温度, 10°C/min 222 / * °C ISO 11357-1/-3
热变形温度, 1.80 MPa 195 / * °C ISO 75-1/-2
热变形温度, 0.45 MPa 200 / * °C ISO 75-1/-2
线性热膨胀系数, 平行 30 / * E-6/K ISO 11359-1/-2
线性热膨胀系数, 垂直 70 / * E-6/K ISO 11359-1/-2
电性能干 / 已调节单位Test Standard
ISO数据
相对漏电起痕指数 500 / - - IEC 60112
Other Standards[S]
相对介电常数, 1MHz 3.7 / 6.8 - IEC 60250
介质损耗因子, 1MHz 250 / 2200 E-4 IEC 60250
体积电阻率 1E13 / 1E10 Ohm*m IEC 60093
表面电阻率 * / 1E10 Ohm IEC 60093
S: These properties are reported by the producer according standards that are different to our defaults.
其它性能干 / 已调节单位Test Standard
吸水性 6.8 / * % 类似ISO 62
吸湿性 2 / * % 类似ISO 62
密度 1260 / - kg/m³ ISO 1183
模塑测量的特殊性能干 / 已调节单位Test Standard
ISO数据
粘数. 145 / * cm³/g ISO 307, 1157, 1628
加工推荐(注塑)价值单位Test Standard
预干燥-温度 <80 °C -
预干燥-时间 4 - 6 h -
注塑熔体温度 260 - 290 °C -
模具温度 40 - 80 °C -
典型数据
加工方法
注塑
特殊性能
高冲击韧性的/经抗冲改性的, 经热稳处理的/耐热的
地区供应
欧洲
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.