Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL™ Resin SE1GFN2 - Europe - (PPE+PS)-GF20 - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL™ Resin SE1GFN2 - Europe:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
加工/物理特性 - 机械性能 - 热性能 - 电性能 - 其它性能 - 加工推荐（注塑）
Any use of this information falls under the rules of our disclaimer.
材料文字说明
NORYL™ SE1GFN2 resin is a 20% glass reinforced blend of polyphenylene ether (PPE) + high impact polystyrene (HIPS). This injection moldable grade contains non-brominated, non-chlorinated flame retardant and carries a UL94 flame rating of 5VA at 2mm and V1 at 1.5mm along with UL746C Outdoor Suitability rating of F1 and RTI of 110C. NORYL SE1GFN2 exhibits high heat resistance, good dielectric strength, dimensional stability, hydrolytic stability, and very low moisture absorption. This material is an excellent candidate for a variety of applications such as solar frames, unattended power supply (UPS) inverter/charger, indoor and outdoor electrical enclosures / housings / connectors, and wall plates / sockets / switches.

UL Yellow Card Link E45329-236777
加工/物理特性价值单位Test Standard
ISO数据
熔体体积流动速度, MVR 12 cm³/10min ISO 1133
温度 280 °C -
载荷 10 kg -
机械性能价值单位Test Standard
ISO数据
拉伸模量 5500 MPa ISO 527
断裂应力 80 MPa ISO 527
断裂伸长率 2 % ISO 527
弯曲模量 4500 MPa ISO 178
简支梁冲击强度, +23°C 30 kJ/m² ISO 179/1eU
简支梁冲击强度, -30°C 30 kJ/m² ISO 179/1eU
Izod impact strength, +23°C, 4mm 25 kJ/m² ISO 180/1U
Izod impact strength, -30°C, 4mm 25 kJ/m² ISO 180/1U
球压硬度 125 MPa ISO 2039-1
热性能价值单位Test Standard
ISO数据
维卡软化温度, A 150 °C ISO 306
维卡软化温度, B 140 °C ISO 306
维卡软化温度, 120°C/h 50N 145 °C ISO 306
1.5mm名义厚度时的燃烧性 V-1 class IEC 60695-11-10
测试用试样的厚度 1.5 mm -
厚度为h时的燃烧性 V-0 class IEC 60695-11-10
测试用试样的厚度 6.0 mm -
厚度为h时的5V燃烧性 5VA class IEC 60695-11-20
测试用试样的厚度 2.0 mm -
热导率 0.28 W/(m K) DIN 52616
灼热丝燃烧指数 (GWFI) 960 °C IEC 60695-2-12
灼热丝燃烧指数 (GWFI) 960 °C IEC 60695-2-12
灼热丝引燃温度 (GWIT) 800 °C IEC 60695-2-13
GWIT - 测试用试样厚度 1 mm -
灼热丝引燃温度 (GWIT) 800 °C IEC 60695-2-13
GWIT - 测试用试样厚度 2 mm -
电性能价值单位Test Standard
ISO数据
相对介电常数, 1MHz 2.9 - IEC 62631-2-1
介质损耗因子, 1MHz 20 E-4 IEC 62631-2-1
体积电阻率 1E13 Ohm*m IEC 62631-3-1
表面电阻率 >1E15 Ohm IEC 62631-3-2
介电强度 30 kV/mm IEC 60243-1
相对漏电起痕指数 225 - IEC 60112
其它性能价值单位Test Standard
吸水性 0.22 % 类似ISO 62
吸湿性 0.07 % 类似ISO 62
密度 1250 kg/m³ ISO 1183
密度 1250 kg/m³ ASTM D 792
加工推荐（注塑）价值单位Test Standard
预干燥-温度 100 - 120 °C -
预干燥-时间 2 - 3 h -
注塑熔体温度 280 - 300 °C -
模具温度 80 - 120 °C -
加料温度 60 - 80 °C -
1区 240 - 260 °C -
2区 260 - 280 °C -
3区 280 - 300 °C -
典型数据
加工方法
注塑
添加剂
阻燃剂
特殊性能
阻燃的
耐化学试剂
水解稳定
应用
汽车
地区供应
欧洲
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.