Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of HOSTAFORM® C 2521 G - POM - Celanese
Material Data Center offers the following functions for HOSTAFORM® C 2521 G:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces
Check here, which other Hostaform datasheets, application examples or technical articles are available in Material Data Center
Use the following short links to get directly to the properties of interest in this datasheet:
| 加工/物理特性 | 价值 | 单位 | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ISO数据 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 熔体体积流动速度, MVR | 1.5 | cm³/10min | ISO 1133 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 温度 | 190 | °C | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 载荷 | 2.16 | kg | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 机械性能 | 价值 | 单位 | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ISO数据 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 拉伸模量 | 2100 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 屈服应力 | 44 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 屈服伸长率 | 12 | % | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 名义断裂伸长率 | 15 | % | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 无缺口简支梁冲击强度, +23°C | 50 | kJ/m² | ISO 179/1eU | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 简支梁冲击强度, -30°C | 50 | kJ/m² | ISO 179/1eU | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 简支梁缺口冲击强度, +23°C | 5 | kJ/m² | ISO 179/1eA | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 简支梁缺口冲击强度, -30°C | 4.5 | kJ/m² | ISO 179/1eA | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 热性能 | 价值 | 单位 | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ISO数据 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 熔融温度, 10°C/min | 165 | °C | ISO 11357-1/-3 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 热变形温度, 1.80 MPa | 84 | °C | ISO 75-1/-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 线性热膨胀系数, 平行 | 100 | E-6/K | ISO 11359-1/-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 电性能 | 价值 | 单位 | Test Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ISO数据 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 相对介电常数., 100Hz | 3.8 | - | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 相对介电常数., 1MHz | 3.8 | - | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 介质损耗因子, 100Hz | 20 | E-4 | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 介质损耗因子, 1MHz | 70 | E-4 | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 体积电阻率 | 1E12 | Ohm*m | IEC 62631-3-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 表面电阻率 | 1E14 | Ohm | IEC 62631-3-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 介电强度 | 35 | kV/mm | IEC 60243-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 其它性能 | 价值 | 单位 | Test Standard |
| 吸水性 | 0.8 | % | 类似ISO 62 |
| 吸湿性 | 0.2 | % | 类似ISO 62 |
| 密度 | 1340 | kg/m³ | ISO 1183 |
典型数据
加工方法
注塑, 薄膜挤出成型, 异型材挤出成型, 片材挤出成型, 其它挤出成型, 吹塑
供货形式
粒料
添加剂
润滑剂, 脱模助剂
特征
热稳定性, 共聚物
耐化学试剂
耐碱性, 耐溶剂性, 水解稳定, 抗氧化性
应用
汽车
地区供应
北美, 欧洲
其他信息
注塑成型
General drying is not necessary due to low moisture absorption of
the resin.
In case of bad storage conditions (water contact or condensed water)
the use of a recirculating air dryer (100 to 120 °C / max. 40 mm
layer / 3 to 6 hours) is recommended.
Max. Water content 0,2 %
Standard injection moulding machines with three phase (15 to 25 D)
plasticating screws will fit.
Conditioning e.g. moisturizing is not necessary.
the resin.
In case of bad storage conditions (water contact or condensed water)
the use of a recirculating air dryer (100 to 120 °C / max. 40 mm
layer / 3 to 6 hours) is recommended.
Max. Water content 0,2 %
Standard injection moulding machines with three phase (15 to 25 D)
plasticating screws will fit.
Conditioning e.g. moisturizing is not necessary.
薄膜挤出成型
General drying is not necessary due to low moisture absorption of
the resin.
In case of bad storage conditions (water contact or condensed water)
the use of a recirculating air dryer (100 to 120 °C / max. 40 mm
layer / 3 to 6 hours) is recommended.
Max. Water content 0,2 %
Standard extruders with grooved feed zone and short compression
screws (minimum 25 D) will fit.
Melt temperature 180-190 °C
Conditioning e.g. moisturizing is not necessary.
In case of very thick wall thickness profiles after-annealing it is
recommended to reduce internal stress.
Annealing temperature 130-140 °C
Annealing time 10 min/mm thickness
the resin.
In case of bad storage conditions (water contact or condensed water)
the use of a recirculating air dryer (100 to 120 °C / max. 40 mm
layer / 3 to 6 hours) is recommended.
Max. Water content 0,2 %
Standard extruders with grooved feed zone and short compression
screws (minimum 25 D) will fit.
Melt temperature 180-190 °C
Conditioning e.g. moisturizing is not necessary.
In case of very thick wall thickness profiles after-annealing it is
recommended to reduce internal stress.
Annealing temperature 130-140 °C
Annealing time 10 min/mm thickness
其E烦龀尚
General drying is not necessary due to low moisture absorption of
the resin.
In case of bad storage conditions (water contact or condensed water)
the use of a recirculating air dryer (100 to 120 °C / max. 40 mm
layer / 3 to 6 hours) is recommended.
Max. Water content 0,2 %
Standard extruders with grooved feed zone and short compression
screws (minimum 25 D) will fit.
Melt temperature 180-190 °C
Conditioning e.g. moisturizing is not necessary.
In case of very thick wall thickness profiles after-annealing it is
recommended to reduce internal stress.
Annealing temperature 130-140 °C
Annealing time 10 min/mm thickness
the resin.
In case of bad storage conditions (water contact or condensed water)
the use of a recirculating air dryer (100 to 120 °C / max. 40 mm
layer / 3 to 6 hours) is recommended.
Max. Water content 0,2 %
Standard extruders with grooved feed zone and short compression
screws (minimum 25 D) will fit.
Melt temperature 180-190 °C
Conditioning e.g. moisturizing is not necessary.
In case of very thick wall thickness profiles after-annealing it is
recommended to reduce internal stress.
Annealing temperature 130-140 °C
Annealing time 10 min/mm thickness
E尾募烦龀尚
General drying is not necessary due to low moisture absorption of
the resin.
In case of bad storage conditions (water contact or condensed water)
the use of a recirculating air dryer (100 to 120 °C / max. 40 mm
layer / 3 to 6 hours) is recommended.
Max. Water content 0,2 %
Standard extruders with grooved feed zone and short compression
screws (minimum 25 D) will fit.
Melt temperature 180-190 °C
Conditioning e.g. moisturizing is not necessary.
In case of very thick wall thickness profiles after-annealing it is
recommended to reduce internal stress.
Annealing temperature 130-140 °C
Annealing time 10 min/mm thickness
the resin.
In case of bad storage conditions (water contact or condensed water)
the use of a recirculating air dryer (100 to 120 °C / max. 40 mm
layer / 3 to 6 hours) is recommended.
Max. Water content 0,2 %
Standard extruders with grooved feed zone and short compression
screws (minimum 25 D) will fit.
Melt temperature 180-190 °C
Conditioning e.g. moisturizing is not necessary.
In case of very thick wall thickness profiles after-annealing it is
recommended to reduce internal stress.
Annealing temperature 130-140 °C
Annealing time 10 min/mm thickness
板材挤出成型
General drying is not necessary due to low moisture absorption of
the resin.
In case of bad storage conditions (water contact or condensed water)
the use of a recirculating air dryer (100 to 120 °C / max. 40 mm
layer / 3 to 6 hours) is recommended.
Max. Water content 0,2 %
Standard extruders with grooved feed zone and short compression
screws (minimum 25 D) will fit.
Melt temperature 180-190 °C
Conditioning e.g. moisturizing is not necessary.
In case of very thick wall thickness profiles after-annealing it is
recommended to reduce internal stress.
Annealing temperature 130-140 °C
Annealing time 10 min/mm thickness
the resin.
In case of bad storage conditions (water contact or condensed water)
the use of a recirculating air dryer (100 to 120 °C / max. 40 mm
layer / 3 to 6 hours) is recommended.
Max. Water content 0,2 %
Standard extruders with grooved feed zone and short compression
screws (minimum 25 D) will fit.
Melt temperature 180-190 °C
Conditioning e.g. moisturizing is not necessary.
In case of very thick wall thickness profiles after-annealing it is
recommended to reduce internal stress.
Annealing temperature 130-140 °C
Annealing time 10 min/mm thickness
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.