Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of FORTRON® 0320 - PPS - Celanese

Material Data Center offers the following functions for FORTRON® 0320:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Fortron datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
加工/物理特性 - 机械性能 - 热性能 - 电性能 - 其它性能
Any use of this information falls under the rules of our disclaimer.
材料文字说明
0320 exhibits a high melt strength for extrusion processes. The material demonstrates excellent heat and chemical resistance. The intended use of this product is for extruding monofilament/fibers, rod and slab. Available standard in powder 'flake' (0320B0), ground powder (0320B0/100 µm), pellet (0320P0) and crystallized pellet (0320C0) form.

Flammability at thickness h (3 mm)V-0-
加工/物理特性价值单位Test Standard
ISO数据
模塑收缩率, 平行 1.2 % ISO 294-4, 2577
模塑收缩率, 垂直 1.5 % ISO 294-4, 2577
熔体的比热 1830 J/(kg K) -
机械性能价值单位Test Standard
ISO数据
拉伸模量 3500 MPa ISO 527
断裂应力 90 MPa ISO 527
断裂伸长率 8 % ISO 527
热性能价值单位Test Standard
ISO数据
熔融温度, 10°C/min 280 °C ISO 11357-1/-3
玻璃化转变温度, 10°C/min 90 °C ISO 11357-1/-2
热变形温度, 1.80 MPa 115 °C ISO 75-1/-2
热变形温度, 8.00 MPa 95 °C ISO 75-1/-2
线性热膨胀系数, 平行 52 E-6/K ISO 11359-1/-2
线性热膨胀系数, 垂直 53 E-6/K ISO 11359-1/-2
厚度为h时的燃烧性 V-0 class IEC 60695-11-10
测试用试样的厚度 3.0 mm -
电性能价值单位Test Standard
ISO数据
相对介电常数., 1MHz 4.6 - IEC 62631-2-1
介质损耗因子, 1MHz 11 E-4 IEC 62631-2-1
体积电阻率 1E9 Ohm*m IEC 62631-3-1
介电强度 18 kV/mm IEC 60243-1
其它性能价值单位Test Standard
吸水性 0.02 % 类似ISO 62
密度 1350 kg/m³ ISO 1183
典型数据
加工方法
注塑, 纤维挤出, 薄膜挤出成型, 异型材挤出成型, 片材挤出成型, 其它挤出成型
供货形式
粒料, 粉料
特殊性能
经热稳处理的/耐热的
特征
熔体强度
耐化学试剂
通用耐化学性
应用
单纤纺丝
地区供应
北美, 欧洲, 亚太, 中南美洲
其他信息
注塑成型
In spite of the minimum moisture absorption a drying of FORTRON is necessary. Predrying in a dehumidified air dryer at 120 degC/3-4 hours is recommended.
On injection molding machines with 15-25 D long three-section screws, are usual in the trade, the unreinforced FORTRON is processable. A shut-off nozzle is recommended.

Melt temperature 310-320 degC
Mold wall temperature at least 140 degC

A medium injection rate is normally preferred. All mold cavities must be effectively vented.
权利义务的法律声明
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.